My 5-lug swap build (z3m content)

[jeffmn8]

My e30 lines matched right up to the m e36 calipers.
There weren't any e36 struts with removable inserts that I've seen. Like said, you have to cut them to install konis or use vw corrado strut inserts like aptyp did.. which makes for a shorter shock housing, reducing bottoming out. I want to upgrade to this setup. I have 94/95(?) E36 non m bilsteins that I converted to coil over with GC parts. The early e36 used the m style swaybar link, which is why I chose that strut. Plus they were cheap on ebay

Thanks, yeah I think I'm just going to pick up a pair of used e36 m3 strut housings and gut them. Then do the GC coilover conversion and reuse my j stock dampers.

[bimmer630]

My e30 lines matched right up to the m e36 calipers.
There weren't any e36 struts with removable inserts that I've seen. Like said, you have to cut them to install konis or use vw corrado strut inserts like aptyp did.. which makes for a shorter shock housing, reducing bottoming out. I want to upgrade to this setup. I have 94/95(?) E36 non m bilsteins that I converted to coil over with GC parts. The early e36 used the m style swaybar link, which is why I chose that strut. Plus they were cheap on ebay

[jeffmn8]

So will I need e30 stainless lines or e36 ones?

[jeffmn8]

If you use E36 M struts you are extremely limited in 16" wheel sizes or use 17" and bigger wheels. <br />
<br />
Do you need these brakes? or five lug or is this for asthetics?

I do need the brakes. The car has an s50 swap and will see plenty of track time. My first event with the car last fall was what made me decide to upgrade the brakes. With pfc06s, I saw brake fade in only 5ish laps with new fluid.

[M-technik-3]

If you use E36 M struts you are extremely limited in 16" wheel sizes or use 17" and bigger wheels.

Do you need these brakes? or five lug or is this for asthetics?

[Roysneon]

You have to cut the strut open remove the guts and then add an insert if you plan to go that method. Many a write up on how to install a set of Koni Inserts into a set of e36 struts. At the same time have the threaded preches put on them from GC and be done with them.

Haha, you posted that while I was off cooking lunch :p That's how I thought it worked.

OP: I found this for you:

http://www.youtube.com/watch?v=qzNZCnUYtzo

Also, you could use blown E36 shocks to cut the tops off of and use the top of your E30 housings that are threaded for the gland nut to reuse your E30 inserts if you want to.

[Roysneon]

From what I've seen online and on non-M E36s I've messed with is that they are a one piece strut that you can cut open for aftermarket strut inserts that fit flush inside the housings and have to have a hole cut in the bottom to add a retaining screw as they do not have a gland nut on the top. Were the struts on your M3 replaced before you got it?

As I said, I have limited real experience with E36s. If you cut open the stock E36 front struts and remove the stock inserts, weld on some GC adjusters/springs and put in Koni inserts that would likely be a low cost coilover system. You could, however also just get an off the shelf system.

An E30M3 master cylinder would match up better than stock for the larger front and rear brakes, but some people forgo it, depends on your usage of the car, I suppose.

[M-technik-3]

You have to cut the strut open remove the guts and then add an insert if you plan to go that method. Many a write up on how to install a set of Koni Inserts into a set of e36 struts. At the same time have the threaded preches put on them from GC and be done with them.

[Roysneon]

Perhaps I'm thinking on M3?

[jeffmn8]

E36s besides 95 M3 have full struts, not housings and inserts like an E30 as I noticed you had listed strut inserts.

Sure about that? I know that my old 98 m3 had strut housings with inserts. I know that coilovers don't use the stock housing, or it gets modified for adjustability.

[Roysneon]

E36s besides 95 M3 have full struts, not housings and inserts like an E30 as I noticed you had listed strut inserts.

[jeffmn8]

Hey everyone! So I just picked up an mcoupe rear end for stupid cheap yesterday so I need to gather parts for the rest of the swap.

Parts acquired so far:
Z3m trailing arms, axles, calipers, rotors, and stub axles.



What I plan on getting:
E36 m3 front - I already have the THR lollipops.
-97-99 Control arms
-97-99 spindle
-New hubs
-Centric rebuilt calipers
-stainless steel lines (e36???)
-front strut housings
-New e30 camber plates.

Now, I'm assuming that I need a new master cylinder (optimally the m3 one) but I've read that it doesn't fit on the booster (which is stock).

So do I need a 7 series 25 mm? Anything else I'm forgetting?

I'm also considering getting rid of my turner j stock setup for a coilover setup.