Loose springs - IE3
Collapse
X
-
I also asked him if it was safe, etc. He said everything is fine and there are 1000's of cars out there that have springs like this. I figure if something bad happens I have emails from him saying this is fine and there is no problem. :DLeave a comment:
-
Of course Jeff is going to say that it is perfectly normal...Wait til I get my sways in. I think those will make a huge difference. I like the setup and have been very happy with it to this point, but to each his own and I respect that.
BTW - I emailed Jeff Ireland for his input.
Edit - He responded saying it is completely normal (mind you he makes and sells the things).Leave a comment:
-
-
Well considering all urethane bushings, ST Sways, M3 Offset, and the Cup Kit I handle very well, and I disagree and did not really enjoy derek's suspension.
I have very little body roll with my setup, the sways took care of most of that.
Hows that clutch replacement going? And you work non stop on restoring a car for a year, it gets old.
And sorry but I will not have suspension that has uncaptive springs, even if I take a handling hit for it.
Wait til I get my sways in. I think those will make a huge difference. I like the setup and have been very happy with it to this point, but to each his own and I respect that.
BTW - I emailed Jeff Ireland for his input.
Edit - He responded saying it is completely normal (mind you he makes and sells the things).Leave a comment:
-
-
And unless you have air jacks, that'd be a totally worthless comparison, as the rate of unloading caused by catching air from a bump and the rate of unloading caused by frantic jacking is orders of magnitude different.
SamLeave a comment:
-
I really can't imagine a situation where IE3's would come magically popping out, they sit in their loose when everything is completely unbolted from the car but they're by no means eays to remove still.Well considering all urethane bushings, ST Sways, M3 Offset, and the Cup Kit I handle very well, and I disagree and did not really enjoy derek's suspension.
I have very little body roll with my setup, the sways took care of most of that.
Hows that clutch replacement going? And you work non stop on restoring a car for a year, it gets old.
And sorry but I will not have suspension that has uncaptive springs, even if I take a handling hit for it.Leave a comment:
-
Seems like you need a lot of reinforcement just to make
a cup kit handle ok, when IE's or KW's and some good dampers handle
very good without all the extras.Leave a comment:
-
Well considering all urethane bushings, ST Sways, M3 Offset, and the Cup Kit I handle very well, and I disagree and did not really enjoy derek's suspension.
I have very little body roll with my setup, the sways took care of most of that.
Hows that clutch replacement going? And you work non stop on restoring a car for a year, it gets old.
And sorry but I will not have suspension that has uncaptive springs, even if I take a handling hit for it.Leave a comment:
-
Not much body roll in the garage eh? :p
Having ridden and driven in stock suspension, cup kit cars, and cars setup like derek's or mine, I definitely think IE3 with bilstein or koni's handles much better than a cup kit setup. my .02Leave a comment:
-
-
yup, is illegal down here to have springs that aren't captive. most people solve the problem by shortening shocks.How is this normal by any means? I've seen vehicles (e30's included) that if they hit a speedbump, pothole, etc can cause the spring to pop out of the hat really easily.
The shock should be matched properly to keep the spring under a LITTLE tension when unweighted.
my
Leave a comment:
-
Not at all. If I cared enough, I'd jack up my subframe to show you how fast GC rear springs lose tension. Completely falling out is another story though.Leave a comment:

Leave a comment: