Announcement

Collapse
No announcement yet.

URGENT - Need to order a couple parts, part number question.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    URGENT - Need to order a couple parts, part number question.

    Hello, I am ordering last few items for my b35 swap and I am looking for the correct part number for the large guibo and correct length bolts/nuts.

    I am using a g260/6 with an early eta driveshaft so it needs a big guibo.

    Is 96mm large or is it small?



    I think that's the correct guibo - 26-11-7-511-454 (old was 26111209168 ?)
    and 12mm nuts 07-12-9-900-047. Yes/no ?
    PN for the correct bolts possibly 26111225486 or is it 27101220647 ?

    Is the Selector Rod joint the same between M10/M20/M30 cars or is it specific to each transmission?

    Finally, clutch slave cylinder. M10/M20/M30 are they interchangable?

    Thank you!
    Last edited by Jean; 07-26-2009, 09:02 PM.
    Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



    OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

    #2
    Pretty sure I got the part numbers for the guibo/bolts/nuts.



    Anybody know about the selector rod joint and slave cyl for sure?
    Last edited by Jean; 07-26-2009, 09:00 PM.
    Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



    OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

    Comment


      #3
      Originally posted by Jean View Post
      Pretty sure I got the part numbers for the guibo/bolts/nuts.



      Anybody know about the selector rod joint and slave cyl for sure?
      My parts were the same for the M20 to M30 trans. The selector fit depending on motor mounting position 2 or 3. I have position 2 and it's angled a little off, 3 would be way out would need a custom plate or race shift from AKG or similar. 96 is the large guibo, I think 78 is the smaller one.

      Comment


        #4
        I am talking about the Shift Rod Joint, not the metal rod itself. It's the joint that slips on the selector shaft on the transmission.
        Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



        OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

        Comment


          #5
          Originally posted by Jean View Post
          I am talking about the Shift Rod Joint, not the metal rod itself. It's the joint that slips on the selector shaft on the transmission.
          Look at this parts breakdown then click on the part you need. It will cross the number over to everything that part was installed on factory.

          http://bmwfans.info/parts/catalog/E3...hifting_parts/

          Comment


            #6
            Perfect, thank you!
            Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



            OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

            Comment


              #7
              Play around with that site. It is better then realoem for crossing over parts and will give pricing in euros and dollars. You can find the hard to find M parts on there as well.

              Comment

              Working...
              X