doin work...(son!) - (vehicle is in pieces, no current pics)
gotta install that shit ^^
Master Cylinder replace ATE Master Cylinder- INSTALLED
bought some bottle caps, painted them black (9 coats of engine enamel each) - INSTALLED
Smoked rear tails INSTALLED
working on fronts and side markers next INSTALLED
finished gutting out the car Interior - COMPLETED
shadowlining the chrome junk (COMPLETED - 5 hours / 110 degrees outside)
antenna removal - COMPLETED
Headlight smoking COMPLETED- need to touch up passenger side, looks fine in daylight, night not so much
Euro Grill Paint and Install COMPLETED
diving board press in TUCKED
Painting aluminum TUCKED diving boards and trim COMPLETED
Rear passenger glass replacement - COMPLETED
Touch up shadowlining (coat 2 and 3) COMPLETED
M3 CABs install - COMPLETED
iS Valance on tucked bumpers + paint match - COMPLETE
painting side mirror housings COMPLETED
4 spoke steering wheel replace - COMPLETED
Interior total repair/paint COMPLETED
Tar and Carpet removal from trunk COMPLETED
HVAC Delete or repair COMPLETED
RSMs COMPLETED
change brakes COMPLETED
next on the agenda -
black leather skipass rear seat - SEARCHING
e36 Steering Rack swap LOOKING FOR BETTER DEAL
Tie rods RECEIVED
Billy sports and HR Race install - IN GARAGE - REAR/Installed -- Front waiting
Volvo Lip sand down and prep - OCTOBER - sanded and prepped, may go another route on lip though
Alpina cluster for m30 swap - IN THE GARAGE
spare tire well delete - OCTOBER
then-
dashboard repair and paint - OCTOBER - Prepped/ More degreasing and sanding
custom Rear Bumper cut and fitment - OCTOBER - bumper in garage
custom side skirt cut and fitment - OCTOBER - skirts in garage
at some point as available in terms of time and money-
Going 5.0 swap, selling m30
Exhaust work....
Bigger wheels for M30 traction (doing fat bottle caps..14x9...)
rivet on DTM flares..possibly IX flares
Updated Pics to come!
Notes for reference on repairs and such
Dash Repair:
303 Aerospace Protectant to prevent further cracking once repaired
basically this:
1. Clean w/ wax and grease remover
2. Sand
3. Clean w/ wax and grease remover
4. Spray the Lord Fusor 602EZ
5. Fill in the holes/cracks with Lord Fusor Bumper Repair Adhesive
6. Sand
7. Clean with wax and grease remover
8. Fill in minor imperfections with a polyester putty/finishing glaze (Anything from Evercoat is good or you can use the Finishing Adhesive that Lord Fusor also carries.)
9. Sand
10. Clean with wax and grease remover
11. Spray plastic adhesion promoter
12. Spray SEM texture coat (might need to sand to get uniform texture)
13. Spray SEM Color Coat
gotta install that shit ^^
Master Cylinder replace ATE Master Cylinder- INSTALLED
bought some bottle caps, painted them black (9 coats of engine enamel each) - INSTALLED
Smoked rear tails INSTALLED
working on fronts and side markers next INSTALLED
finished gutting out the car Interior - COMPLETED
shadowlining the chrome junk (COMPLETED - 5 hours / 110 degrees outside)
antenna removal - COMPLETED
Headlight smoking COMPLETED- need to touch up passenger side, looks fine in daylight, night not so much
Euro Grill Paint and Install COMPLETED
diving board press in TUCKED
Painting aluminum TUCKED diving boards and trim COMPLETED
Rear passenger glass replacement - COMPLETED
Touch up shadowlining (coat 2 and 3) COMPLETED
M3 CABs install - COMPLETED
iS Valance on tucked bumpers + paint match - COMPLETE
painting side mirror housings COMPLETED
4 spoke steering wheel replace - COMPLETED
Interior total repair/paint COMPLETED
Tar and Carpet removal from trunk COMPLETED
HVAC Delete or repair COMPLETED
RSMs COMPLETED
change brakes COMPLETED
next on the agenda -
black leather skipass rear seat - SEARCHING
e36 Steering Rack swap LOOKING FOR BETTER DEAL
Tie rods RECEIVED
Billy sports and HR Race install - IN GARAGE - REAR/Installed -- Front waiting
Volvo Lip sand down and prep - OCTOBER - sanded and prepped, may go another route on lip though
Alpina cluster for m30 swap - IN THE GARAGE
spare tire well delete - OCTOBER
then-
dashboard repair and paint - OCTOBER - Prepped/ More degreasing and sanding
custom Rear Bumper cut and fitment - OCTOBER - bumper in garage
custom side skirt cut and fitment - OCTOBER - skirts in garage
at some point as available in terms of time and money-
Going 5.0 swap, selling m30
Exhaust work....
Bigger wheels for M30 traction (doing fat bottle caps..14x9...)
rivet on DTM flares..possibly IX flares
Updated Pics to come!
Notes for reference on repairs and such
Dash Repair:
303 Aerospace Protectant to prevent further cracking once repaired
basically this:
1. Clean w/ wax and grease remover
2. Sand
3. Clean w/ wax and grease remover
4. Spray the Lord Fusor 602EZ
5. Fill in the holes/cracks with Lord Fusor Bumper Repair Adhesive
6. Sand
7. Clean with wax and grease remover
8. Fill in minor imperfections with a polyester putty/finishing glaze (Anything from Evercoat is good or you can use the Finishing Adhesive that Lord Fusor also carries.)
9. Sand
10. Clean with wax and grease remover
11. Spray plastic adhesion promoter
12. Spray SEM texture coat (might need to sand to get uniform texture)
13. Spray SEM Color Coat
Comment