Unbeatible Beater Build - 87 BMW 350is

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • stevegolf
    replied
    Been a while since an update. Two major items were going on at the same time, the engine block refurbishing and re-doing the engine bay. I can happily say both are done.

    I decided to go with a Ford blue for the bay to make the V8 feel at home. That meant stripping the bay, grinding off the paint and rust, and priming it. This took a while going a section at a time. Since a lot of it is going to be covered I just hit the most visible damaged areas with some bondo.



    Then I masked it off and sprayed it. This was my first non rattle can paintjob. I got the gun for almost nothing at the local industrial auction. I had to thin the paint a bit before the spray was fine enough, but once that happened it went quick and was fun. The paint is engine enamel, so it should be strong and I used almost 2 pints on it. The Ford blue rattle cans I got had more glittery flakes to it so I misted a can of that on as I went. Added a heavy clearcoat. Can't wait to wetsand/buff it out. Its a really cool blue, I'm so glad to have it done, not half ground up, half primer, and half old crappy paint.







    I think it looks pretty good.



    There are some runs and imperfections but is a $500 car's engine bay. When it is polished it will look 100 times better than the outside which is what I was going for. I'm going to have to find a set of the stock BMW stickers and put them back on. I'll need to have the color sticker remade, maybe fordenblau.

    Of course now I'll be extra picky on putting the old parts back in. Going to have to clean a lot of them up, don't want dirty old looking parts attached to a shiny new bay.

    Speaking of shiny new parts, I picked up the engine from Automotive Machine in Fraser. Man, it looks brand new. Decked, line bored, balanced, had to go 0.02 over on the pistons, new plugs, bearings pressed, new pistons and rod bearings installed, polished crank, oil pump and shaft, as well as all the gaskets and probably a few other things. Really happy with how it looks and the service. I spent more than what I was at first planning (just getting it cleaned and checked) but its well worth the piece of mind knowing its been refurbished and will run really well vs. not knowing if it would crap out after putting in all the work with getting it installed.

    The money shot





    So thats all exciting. I still haven't sold the old engine which is taking up a ton of space in the garage. I'll practically give it away at this point. I have a ton of stuff to do now and I have most of the parts to do it with. Don't have a trans yet but that will have to wait until my wallet recovers.

    Woodward was also way too ambitious for the timing. I think next year's Eurohangar is a good goal.

    Leave a comment:


  • Eddie Lives On
    replied
    Originally posted by z6ne
    thanks, I'm gonna try to buy one
    Looks like the one I have in my car. PO told me 2002 as well.

    Leave a comment:


  • z6ne
    replied
    Originally posted by stevegolf
    Heard back from the P.O, its most likely from a 2002 but was in an older E28 that he bought.
    thanks, I'm gonna try to buy one

    Leave a comment:


  • FilthyFarmKraut
    replied
    subscribed

    Leave a comment:


  • stevegolf
    replied
    Originally posted by z6ne
    nice work. Where can I get that shift knob in the 4th picture from the bottom?
    Heard back from the P.O, its most likely from a 2002 but was in an older E28 that he bought.

    Originally posted by eurotrash
    Looking good. I would have stayed efi (this is coming from a carbed guy). Ill be running an exploder motor as soon as i can find a decent donor and efi will def stay. The double pumper is fun but i get like 8mpg and it can get a bit finiky sometimes.
    Thanks. I may switch to EFI some day but I'm a lot more comfortable with carbs. Mileage isn't too big a concern since it is my 3rd car but I may feel the need to mess with it some more once its running well.

    Originally posted by FunfGan
    Looking good, best of luck!
    Thanks man! I read through your build before starting mine. Definitely an inspiration for my project. :D

    Leave a comment:


  • FunfGan
    replied
    Looking good, best of luck!

    Leave a comment:


  • eurotrash
    replied
    Looking good. I would have stayed efi (this is coming from a carbed guy). Ill be running an exploder motor as soon as i can find a decent donor and efi will def stay. The double pumper is fun but i get like 8mpg and it can get a bit finiky sometimes.

    Leave a comment:


  • stevegolf
    replied
    Originally posted by z6ne
    nice work. Where can I get that shift knob in the 4th picture from the bottom?
    Thanks, it was installed by the PO so I sent him a message, I might try to find the same one.

    Leave a comment:


  • stevegolf
    replied
    Originally posted by dougie30
    is that a b4 passat i see in the background?
    Yup it's my brothers car. He'll be selling it in a month or so if you are interested. :)

    Leave a comment:


  • z6ne
    replied
    nice work. Where can I get that shift knob in the 4th picture from the bottom?

    Leave a comment:


  • dougie30
    replied
    is that a b4 passat i see in the background?

    Leave a comment:


  • evandael
    replied
    yeeah, back over here from TCL!

    i, too, look forward to your progress.

    Leave a comment:


  • willworkfore30s
    replied
    sub'd

    Leave a comment:


  • stevegolf
    replied
    Been a month since the last update and I've made some decent progress since then. I bought a used parts washer from an industrial auction for about 1/4th the price of a new one. I didn't take into account the cost of cleaning all the crap out from its past life, which took about two hours. It was still really nice to have and made short work out of the heads. Got all the gunk off and gave them a fresh coat of paint. I was surprised by how good they look compared to when I got them.







    I beadblasted the pistons. It would've been ideal to soda blast them to not worry about debris but beads are less abrasive than sand. It was like painting the dirty pistons with clean. All the gunk disappeared. They came out looking nice. My uneducated eye didn't see any abnormal looking wear on them so they'll be reused if possible. I'll definitely be borrowing this beadblaster again in the future. On the valves in the short term.





    I finished disconnecting everything to pull the engine. The clip holding the shift linkage pin to the trans was designed by a bad man who should be ashamed. The clip wrapped over the top of the bracket where you can't see or reach. It took 20 minutes to see what it was and 20 more to pry it out.





    It was nice to see a clear opening. The E30V8 instructions say you don't need to modify the pass-through much if at all. I have to decide if I want to keep my stock //M shifter or get something different. My old E28 had a wood one which I liked a lot. I'll have to keep looking around. I don't want anything obnoxious.



    Had a big weekend last weekend. My brother came to visit and we all worked on our cars which was pretty fun. My buddy was doing a lot of stuff on his Challenger. Came out looking good. I started pulling the engine.





    I got a leveler at the industrial auction which was essential. Since I left the trans on it would've been impossible to pull it, at least safely. Speaking of safety, while the engine was almost out and we were lifting it and tilting it to clear the front of the car the rear chain snapped. One of the links exploded and the bottom of the trans swung and hit the front of the car. My brother was standing on the bumper adjusting the leveler and jumped clear of the car. It was a little scary, thankfully it didn't swing too far and do any damage. The hook and everything looked fine, the one link was just missing. We didn't find any pieces of it yet which is weird.

    We reattached it and got it out. After putting it on a pallet it rolled over and barfed a stream of coolant on the garage floor. After more than 300,000 miles it finally died. Hopefully I can sell it and someone will get some use out of it. We started grinding the paint off which is actually kind of fun except for the dust. I will definitely wear a mask for the rest of it.



    I got some Ford blue paint and filler primer for when its all clean and fixed up. The shiny dark blue engine bay will be a nice contrast to the faded, rusty, red outside. I'll be painting the block black which will look cool with the red headers. I've been looking at different valve covers but don't want to drop the money on that quite yet. I've got plenty of other parts to find to get it together.

    As far as parts goes, I picked up some K&W springs and Bilsteins off the forums. There are some other suspension upgrade parts to get before installing those. Also picked up a Holley blue fuel pump and FPR from Craigslist. The dude I got it from was pretty cool, it was running on the same engine in his Mustang. I also picked up an E34 remote brake booster which I can start fitting up now that the engine is out.

    The machine shop said the block looked good and the crank just had to be polished. They'll be boring the cylinders, decking the block and installing some bearings and freeze plugs. Some buddies will be helping me rebuild the engine. This will be my first engine rebuild and I'm pretty excited to get going on it. I have plenty of other stuff to do in the meantime.

    I'm pretty positive I won't have it ready by Eurohangar at the end of June. Once everything is together I still have to get a custom driveshaft and exhaust made and installed. My new goal is Woodward which shouldn't be a problem, I hope.

    Leave a comment:


  • stevegolf
    replied
    Cool sounds good, let me know when you guys are going out. Won't be driving the e30 for a while but my miata will be running soon. Just saw a nice gold e30 convertible driving on Woodward today.

    Leave a comment:

Working...