A trip down memory lane...89' 325is + S52 inside!

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • DEADZONER1
    replied
    congratulations.....great job

    Leave a comment:


  • Scallywagon
    replied
    Nice job stubob :up:

    Leave a comment:


  • gkurey
    replied
    I've got video!

    Leave a comment:


  • gkurey
    replied
    Thanks for the props, guys! I've been married for exactly one month now, and I must say I love the lifestyle...and the fact the wifey has been encouraging me to get out in the garage and finish the e30. Today I hit a major milestone...I got it started up! It all started this last weekend...as I posted in my last update, I needed to build an exhaust, replace some brake lines, install the clutch line, bleed the system, and fill the motor with oil/coolant/ps fluid, and crank it up.

    I started with the exhaust...I decided to build the headers down into one 2.5" pipe, build in 2 O2 ports, one for the factory sensor, one for wideband at a later date, and then merge into the aft section of the e36 exhaust I had. Building the merge was time consuming, and not the prettiest, nor did I get many pics, but its decent! I went catless and am utilizing the e36 resonators and rear section, the rest is all me. I'll let the pics do the talking...







    The fitment came out really well IMO...scope how closely it fits to the body!





    I will post pics of the rear section when I finish modifying the rear muffler for the e30 bumper. As for the brake lines...this was the reason for replacing:



    Due to budget constraints, I just replaced with new OEM lines. I then bled the system using a Motive Power Bleeder which made the job a snap, filled with ATE Super Blue of course. After that, I installed my TRM chip, put in a new battery, filled the engine with fluids, and pulled the fuel pump fuse so I could crank it to prime the motor w/oil. So, I key up the ignition, twist the key, and....nothing :( I ran out of time (this was Sunday) due to need to go to a friend's wedding, but I vowed to figure it out today (Monday).

    Today, I got off work and was wondering how it would be possible my starter wasn't working. I immediately thought maybe I mixed up some wires on the starter, but its hard to mix up wires on the starter IMO, since the lug diameter pretty much ensures you only install one way, so I thought I'd look for something even easier. After about 10 minutes of looking, I found the culprit...I forgot to install the motor-chassis ground cable! I didn't have the one from the S52 or my M20, but I had a cable off an old nissan of mine that was just the right size. I threw the cable on, reconnected the battery and cranked it up...turned over just fine! I cranked until the low oil pressure light cleared, and then reinstalled the fuel pump fuse for the real deal...It cranked up on my second try...the first one was getting fuel all the way up to the rail I'm guessing.

    So far, it idles incredibly smooth on the TRM tune. I only ran it for a few seconds today, and I need to rebleed my clutch before I drive, but I'm looking forward to the test drive either tomorrow or the next day! Thanks for looking guys...look forward to more updates as I can finally get to work on the cosmetic side of the car and cleaning up the engine bay!

    Cheers!
    -Gavin

    Last edited by gkurey; 10-12-2010, 07:41 AM. Reason: Misspeller....grrr

    Leave a comment:


  • MR E30 325is
    replied
    Mitch500, you can rethread the stock single pin brown top M20 temp sensor and thread it into the throttle body heater hole. Though you remove the throttle body heating function, which you will need in cold places.

    Gret build, and congrats on the engagement!

    Leave a comment:


  • mitch500
    replied
    what are guys doing these days about the dual temp sensor issue with the s52s? did you tap the head or are there ways around this now to get your temp gauge to work?

    Leave a comment:


  • CorvallisBMW
    replied
    Wow nice build! I love the attention to detail on the strut modification, they look great. Congrats on getting engaged too! Keep us updated, I love build thread likes this.

    Leave a comment:


  • gkurey
    replied
    Hey guys...long time since I've updated. Last I left off, I was about to install my suspension. Usually that takes an afternoon, but this kit requires a bit of welding and modification to the front spindles. This update focuses on the process. I would have posted this a month ago, except for half way through, I found out the kit I had was for the 4cyl e30s w/ smaller front shock tubes...oops. The vendor I got the kit from was cool though, and they helped me exchange for the 6cyl version. So after all that, I can now post the installation. Here we go:

    First order of business is to remove the OEM suspension and tear it down to a bare spindle/shock tube.


    Next, I cut off a majority of the shock tube, leaving approx 2" as a guide for the weld-on coilover mount.


    Then, since we're going to be welding and we want good, solid welds, I cleaned up the spindle by removing paint and contaminants with a wire wheel!


    After that, I checked the fit of the weld-on mount with the spindle. Very tight fit but thats good...since the mount slips over the old shock tube, perfect suspension geometry can be ensured.


    The next step was super crucial. The spindle was pre-heated using a torch for ~10-15 min to help reduce material/thermal stresses created from welding to prevent the cast iron spindle from cracking. This also would help with the penetration of my little flux-cored welder to get a good weld. Welding cast to steel is tricky, but the results are great if the proper prep is done.


    welding...


    And the final result...They aren't the greatest looking welds...I did this on the garage floor...no work bench, not sitting, etc etc, but the toes of the welds show adequate penetration and I feel that they will hold up to the abuses of driving just fine! That being said, I miss my old 210v Lincoln MIG that I had to sell before I moved out here...but this little 90$ harbor freight FCAW isn't too bad at all either! I'm pleasantly surprised (I bought it just for this and to make my exhaust).


    Next...wash, rinse, repeat on the other side and paint the bare metal to prevent future corrosion!


    Finally, with the correct damper for my car...the front suspension is ready for installation! Looks sexy IMO


    On the car with the wheel back on! Looks great and will go a lot lower. I intend to lower that car a bit more once I'm done working on the exhaust.


    So the suspension is now done, the driveshaft is installed and I am working on the exhaust. I'll post pics of that tonight perhaps. I am running an OEM e36 M3 exhaust all the way through (I want it quiet lol). Turns out it needs a lot of work to be installed, but its cheap since I already had it as part of the swap deal and according to others, it sounds good.

    After the exhaust, all I need to do is install some SS brake lines, install the clutch line, bleed the system, fill the motor with coolant and oil, and crank it up! I'm getting very close!!

    Thanks for reading guys!

    Leave a comment:


  • ak-
    replied
    What a good sport.
    You're a lucky guy; Good luck with the build!

    Leave a comment:


  • bimmer_E30
    replied
    Awesome thread!

    Leave a comment:


  • Dude
    replied
    Awesome thread is awesome. Stoked for the pics when its all done.

    Leave a comment:


  • J3M93
    replied
    You're a lucky man Gavin, a lucky man

    Leave a comment:


  • GuercII
    replied
    Congrats. Looks like a cool project, and that is a clean engine! You're also lucky to find a girl that tolerates a lot of time in the garage. Keep those pictures coming.

    Leave a comment:


  • gkurey
    replied
    Hey guys...sorry its been so long since I've posted. Work and other things in life have pretty much kept me from getting on here to do a decent update...but I have done a lot of work on the car since my last update 2.5 months ago. Progress is a little slow, but new financial obligations (got engaged, WOOT!) have kept progress on the slow side as well as just having time due to my rotating shift work schedule. The fiance encourages me to work on it often though, so here is what I've got to report:

    Last time I posted, I was tearing down the S52 and getting it ready to go in for the swap. I dropped off the rear sump pan and swapped in a pan from an e34. This went well except for a major issue that popped up later (I'm updating chronologically, so bear with me)...

    Here is a shot of me tearing down the S52 on the stand.


    A shot of the engine with the e34 pan installed. While the pan was off, I loctited the oil pump nut as well as galled the last thread to keep it on.


    I also proceeded to install a new waterpump and a new thermostat of lower temp.


    The flywheel looked really good and I found a place that would machine it instead of buying a new one...only took ~.01 off to make it nice again.



    That same night I put the tranny back on and got it ready for install into the e30 chassis.


    Fast forward another day and I got the m20 out...pretty easy to remove! I had a garage full that night!


    While the engine was out, I took the opportunity to do the e36 rack swap. A lot of people i saw were cutting and using aluminum spacers. I used some delrin spacers I found at lowes....worked well!


    After a little cleaning and the rack swap, I was ready to put the S52 in. Its pretty long so I had to get an extreme angle to get it in. My fiance was a good helper that day!


    This is where I started noticing a problem with the oil pan install. After having the motor at that angle, but unfortunately after getting it resting in the car, I noticed an oil leak already from the pan/front timing cover/block intersection on the passenger side. I know if its leaking now, it surely will leak with oil in the system. So I had to step back, take off the rack, and drop the pan. This was not easy and really stunk. I didn't know but apparently you are suppossed to use a sealer as well as the gasket. I reinstalled using my favorite gasket maker "The Right Stuff" and I'm hoping no leaks upon filling this system this weekend.

    Here is a pic of the motor just after install, no wiring or anything:


    As many people know, the factory brake booster must be changed to run a DOHC motor due to the intake manifold hitting it. Given many choices, I went for the cheapest possible. I scored a 944 booster from ebay for 15 shipped haha! Here is a pic of the size difference, 944 Left, 325 Right.


    Even after this, I've probably only got 1-2mm of room...CLOSE! This is a test fit of the intake manifold. Oh yeah, thats 1-2mm even after shaving the fins off the intake mani.


    A lot of people seem to get rid of extra systems, but for this project, I wanted to keep most things intact if possible. I was able to keep the fuel charcoal canister by moving it back a few inches under the brake MC by just flipping the bracket!


    The rest has been fairly simple...swapping sensors for my OBD1 conversion, hooking up the wiring harness, hooking up coolant lines, hooking up vacuum lines, etc. The last things I need are a lame throttle cable bracket, then I can hook the throttle cable up properly and a chip; oh and exhaust.




    For the exhaust, I've got the e36 obd2 system that came with my motor that I may or may not try to make work. It looks like it will need some heavy modification.

    Also, I'm working on installing my coilovers. Got some from BC racing. Construction looks good enough, but there is one issue. The portion that requires welding on to the knuckle is too narrow to accept the e30 shock housing diameter. Upon question the manufacturer, it seems the early e30s had narrower shock bodies and the seller who I got these from sold me the wrong kit. New shock mounts are on the way so I can finish the install. Here's the disassembled driver side, new tie rod end awaiting new damper...


    And the new dampers....pretty sexy!


    Thats about where I am for now...so close to a start up I can taste it! I will try and post more frequently....gonna fill the system with water and oil this weekend and try to kick it over for the first time. Progress on the A/C system will be slow until after the wedding in Sept. but I expect to tie up a lot of loose ends around then. Also, I forgot to mention that I installed a Flexalite 16" pusher pan in front of the condenser, and ordered a lower temp fanswitch to work since I wont be fitting in the OEM clutch fan.

    Oh, and for those who threatened me with ban if I didn't post more pics of the fiance...here she is (disregard me being in the pics, lol)





    Cheers,
    Gavin
    Last edited by gkurey; 07-02-2010, 01:22 PM. Reason: I suck at posting

    Leave a comment:


  • E30Nova
    replied
    Originally posted by fiftytakedowns
    pics of GF or ban
    +1

    Matt

    Leave a comment:

Working...