Those seats look awesome with the suede. Is the rear staying original?
-
-
Rear is getting the same treatment, didn't have time to snap pictures of the rear but Ill put some up once I'm down at the shop tomorrow.Comment
-
Looking good mate!
Originally posted by RoysneonOriginally posted by MarkDComment
-
Kylie should be finishing up this week once we get headers and install the interior and exhaust!Comment
-
What kind of headers you guys going with? interested in what you guys have in mind for the exhaust.sigpicComment
-
Going Stromung for the exhaust. Not 100% on the headers yetOriginally posted by Motorsports View Post
Plus side, the headliner is done.Comment
-
I love my Stromung exhaust. Not too loud and has a nice tone to it.
Originally posted by RoysneonOriginally posted by MarkDComment
-
I am really looking forward to hearing the Stromung exhaust in person!Comment
-
Promise there will be pictures soon. Been in the shop the past two days with Levent and Joel, with Nico chipping in.
Interior is almost completely done. HVAC unit still needs fixing along with the Gauge cluster needs updating (5000rpm is not enough for an IS motor )
Exhaust was going in tonight.
Completed at the end of the first phase
M20 IS Motor and 5 speed Swap
M20 Maintenance Pack- Timing Belt, Plugs,
Thermostat, Water pump, All radiator hoses, Belts,
Valve Cover Gasket, Oil Pan Gasket(Paper),
Intake Manifold Gasket, Head Grommets, Breather
Hose, Oil Filter Housing Seal and Plug, Oil Filter,
20/50 Oil, Shifter Support Bushing, Exhaust
Manifold Gaskets, Spark Plugs
Getrag 260 Maintenance Pack – New Clutch, SS
Clutch Line, Selector Seal, Center Support, Guibo,
Shifter Foam, Output Shaft Seal, Selector Seal,
Clutch Pin, Fresh Redline Fluid
Head Gasket Kit
Head Bolts
Ireland Engineering Aluminum Light Flywheel
Powder Coated Manifold(wrinkle Black and Valve
Cover(Wrinkle Red GPS)
Z3 Short Shifter
Euro Bumper Set
Euro Valance
Ireland Engineering 22/19 Sway Kit
Black Rear Deck
Euro Bumper Set-Powder Coated Semi Gloss
Black - Repaint Trim
19lb Injectors (Flow Matched) and Mark D
Chip(New)
173 ECU w/ Mark D Chip installed
Misc Parts – HVAC Panel reinstalled
M3 Steering Rack
Brake Kits – Zimmerman Coated Rotors, UUC SS
Brake Lines, New Pads, Fresh Fluid
HR Sport Springs with Bilstein sports
E90 Drop Hats
New Battery
Stromung Exhaust
Rear Pipe Joint Section
Rogue Rear Shock Mounts
Rear Exhaust Shield
Wire Shield
New Flex Disc and Center Support
Cans of Undercoating – As needed for touch up
spots
OE New Tire Rod Assemblies with new Boots
Control Arm Bushings
Repair one boot on control arms – No need to
replace entire control arm.
Head liner Dyed
E brake Console reinstalled
OE Cat Mid Section
Exhaust Mounting Kit
Shifter Boot Kit – Black Leather
ZHP Shift Knob
Sunroof Crank OE
IS Side Skirts – New
Thinking about picking up a satellite radio for the car (maybe an alpine, to go with the alpine white)
2nd phase of the restoration will be the following (within the next year)
Full AlpineweissII painjob
Powdercoat/blackout chrome trim
Smoked Euro Elipsoids w/ HID headlamps
Euro Grill
Red tails (bye bye orange)Comment
-
Wow. Thats a serious assortment of parts. Going to be LEGIT once its all said and done!!!IG: deniso_nsi Leave me feedback here
Comment
-
Joel is the man!!Comment
-
Nice build list, pic would be nice to back it up ;) Keep up the good work!Comment
-
Been a while since the last update.
Officially the engine is fried at the moment. The first start up did not go to well. We are going to be pulling the engine and replacing it.
Looks like about 8 days away till we get a new motor to drop in. Almost pulled the trigger on a 24v setup but a little too far out of the budget at the moment, and I'd rather spend that on a paintjob.
I will be trying to get down to Guten soon, I have been away from Levent and Joel for a couple of weeks as I have sold my 335i and I am carless :(
Pictures soon. Taking requests! :)Comment
-
Do you need a engine? If so hit me up.Comment
-
Motor Problem solved.
It has more valves.... More to come soonComment
Comment