No Budget Build "The Glorious Piece of $hit"

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • jamesthebikeguy
    replied
    Update: Suspension!

    About a month ago I purchased suspension off of a e30 race car. This car was prepared and built by Korman Autoworks.

    I purchased the whole suspension bits, and the rear sub frame and everything attached.

    The suspension consists of:
    Korman Custom Valved Bilstein Shocks
    Korman Selected Coil Springs
    Korman Billet Rear Strut Mounts
    Korman Front Adjustable Camber Mounts
    Korman Swaybars 22mm Front, 19mm 2 Position Rear
    Korman Adjustable Endlinks, and Polyurethane Bushings

    Rear Subframe:
    Derlin Control Arm Bushings
    Derlin Subframe Bushings
    Goodridge Brake Lines
    New Wheel Bearings
    Calipers and Ect. Hardware.

    I only installed the suspension did this yesterday and took the car off the lift today give her a test ride.

    Pictures are in chronological order:












    Broken Rear Coil Spring:




























































    Now the good pics, the front camber is set as far in as it can, will get it aligned soon because I am sure I am running too much camber.

















    Leave a comment:


  • jamesthebikeguy
    replied
    Originally posted by einstein57
    Put the green paint away!!!! Atleast till you have some power to back it up.
    Not likely, Green paint stays and I doubt there will ever be more power in this thing.

    Originally posted by Pantless Spency
    to much black!!!! i can dig the mirrors but not the tails, valence, skirts, and rear valence. also wheels..
    but it still is an e30 :)
    Blacks the new white...

    Originally posted by davem
    you should have painted the front valence white like it's supposed to be! that being said you've done an awesome job!
    When it was white you could see that the body is junk. Paint it black and no one notices. This aint the showroom model

    Originally posted by Mike The Bavarian
    paint the front and rear valence white and it'll look alot better
    Noted however not changing.

    Anyways more pictures today of this car. I need Badges and my suspension installed bad...










    Leave a comment:


  • Mike The Bavarian
    replied
    paint the front and rear valence white and it'll look alot better

    Leave a comment:


  • davem
    replied
    you should have painted the front valence white like it's supposed to be! that being said you've done an awesome job!

    Leave a comment:


  • Pantless Spency
    replied
    to much black!!!! i can dig the mirrors but not the tails, valence, skirts, and rear valence. also wheels..
    but it still is an e30 :)

    Leave a comment:


  • einstein57
    replied
    Put the green paint away!!!! Atleast till you have some power to back it up.

    Leave a comment:


  • lostininglewood
    replied
    Me like.

    Check out the link below, lots of people have used the same paint, great results, however they rolled it on. Will give you tips to bring out the shine!

    http://board.moparts.org/ubbthreads/...fpart=all&vc=1

    I'm thinking of doing the same.

    Leave a comment:


  • jamesthebikeguy
    replied
    Originally posted by oekundar
    James- I hate to break it to you, but no one is going to care too much about the lime green mirrors since you have and continue to post pictures of cleavage in this thread.

    carry on....:)
    You noticed my diversion tactics did you?

    Leave a comment:


  • oekundar
    replied
    James- I hate to break it to you, but no one is going to care too much about the lime green mirrors since you have and continue to post pictures of cleavage in this thread.

    carry on....:)

    Leave a comment:


  • jamesthebikeguy
    replied
    Update after a lot got done:

    Time to paint trim and the lowers of the vehicle so I can complete the paint job.










    Even stripped (aircraft paint stripper) the window wipers and painted them to remove the rust.


    Tinted the tail lights:

    Sanded with 2000 grit, cleaned with paint thinner and then went to town with Rustoleum tail tint. I searched around but could not find a single place with VHT in stock, as I have had good luck with it in the past. This rustoleum is ok, I hate the spray nozzle.





    More on this later.

    And done for the evening


    Next Day:

    I wet sanded the tinted lights with 2000 grit then wet sanded down to 2500 grit. I used a orbital buffer with polishing compound to do the rest.


    Decided to take obligatory vain pictures of my Glorious POS






    Time to sand down the mirrors. This is the bit of rice I feel I need to complete the e30. Hate as I sure you will, I love it!





    Purchased a oil pan ground cable from a member making these on e30tech. This thing looks sweet and compared to the old one it is way better.

    Almost looks like no sheathing is left at all.

    Now for Tie-rods for both sides, the rejection sticker that has been defacing my windshield is because the passenger side Tie-rod was way sloppy, figured might as well replace both while I am at it.



    Of course as with any of my Mods, gotta rep the Lime green.



    And the Rice, behold Lime green mirrors that match absolutely nothing on the outside.






    Thanks for viewing expect to see the following in the coming days:

    1. 1999 540i Sport Blk/Blk. I just purchased her today (8/24/11)
    2. Removal of interior completion
    3. Installation of my Korman suspension including camber and sways

    Edit: Added quick pic this morning before work
    Last edited by jamesthebikeguy; 08-25-2011, 03:59 AM.

    Leave a comment:


  • jamesthebikeguy
    replied
    Quick update on the car, Last night I was able to paint the trim and valance so here ya go, finished product I'll post pictures of the process later.





    Leave a comment:


  • DuMa
    replied
    the sunroof shape grooves would drive me nuts.

    Leave a comment:


  • freeride53
    replied
    kewl

    Leave a comment:


  • Dirtsquirt
    replied
    What a clapped out POS.

    What was the reasoning behind shaving the rear window wing panels?

    ...and not removing the bumpers before paint.

    Leave a comment:


  • yert315
    replied
    What's the plan for the front and rear valence?

    Leave a comment:

Working...