This Is Pictures.

[LowR3V'in]

Nice. I thought it was an underwater pic.

[riverdale21]

Work pics... I waffleswaffleswaffles live at work.

Doosan DA40 with a Scania 13 liter inline-6 cylinder turbo diesel. Continuation of post from a few months ago... going around the south east performing Tier 4i emissions related testing and updates for the OEM. This thing dwarfs my work van.








Matching pair of Cummins NT855F4 fire pumps before rebuild. One engine got new turbo, injectors, injection pump, and water pump. Blue printed the top end and had the fuel system and turbo built to our spec. 340HP and 890lb-ft @ 2000RPM was the estimated output. Other engine just got new head gaskets, valve job, and injection timing.



Downtown Atlanta pictures again from the roof of the Marriott Marquis. Sorry if some of them are the same as previous post.





If anyone has ever been in the Marquis (or seen the Denzel movie Flight) the whole hotel is open from the atrium to the roof. This picture is looking from the skylights down as far as the camera can see. It was too bright out and mostly got my reflection. If you squint and tilt your head just right you can see it.


Replaced the ENTIRE wiring harness (engine, generator end, controls) for this genset after a control panel fire. Had a custom control panel enclosure built too as that was too far gone to repair. Wish I had better pictures.




Another similar wiring job. Conversion from all analog controls to fully digital, complete wiring install.


Spotted a clean Sylvia conversion in Roswell


Mitsubishi S16R 64 liter quad turbo 16 cylinder playing around while reassembling after rebuild



Couple of turbos and water pumps next to 5 gallon buckets


Spotted in traffic


New 3 series with M-Par's. Not bad


Veyron goodness



4 hours of continuous full load operation... cherry turbo




My old E34

[mrsleeve]

^

Nice Moxy truck I hate those things..................... I have a lot of hours sitting in one of those POS shit piles. Yeah they have decent power but you cant see shit behind you because of how the have the dump body set up. At least with a CAT or Volvo the dump bodies are wider and flatter and form the operators seat you can see over them and look behind you while backing up.

here is a about the only shot from this job I have, its a quick one and outta the window of my truck (notice the A pillar on the right)

[riverdale21]

^

Nice Moxy truck I hate those things..................... I have a lot of hours sitting in one of those POS shit piles. Yeah they have decent power but you cant see shit behind you because of how the have the dump body set up. At least with a CAT or Volvo the dump bodies are wider and flatter and form the operators seat you can see over them and look behind you while backing up.

here is a about the only shot from this job I have, its a quick one and outta the window of my truck (notice the A pillar on the right)

The only time I get to drive them is to put some heat in the engine to get the EGTs up. Mostly there to work on the engines. Seems like they would be a blast to tool around in.

One of our Scania customers had a roll over on a Terex TA300. Engine only had about 90 hours on it. Once the unit was upright the customer tried to crank it without looking it over. There was about 5 gallons of oil in the pistons during crank over. Needless to say I've got a rebuild in the future. I'll have to get some pictures of that.

[mrsleeve]

LOL yeah you have not run one if you have not flopped the dump body over a time or 2, its not a matter of if but WHEN when it comes to those dam things and the Moxys (or dosan's) are much easier to flop over than CAT or Volvo. I have never taken the cab over, though I have come close on a steep hill side about a decade ago

[Deltron Dirty30]

[LJ851]

This is awesome.

[Deltron Dirty30]

yes it is.

I thought i disliked stingrays till i saw that car.


it is Brian Hobaugh's 1965 Corvette

[E30 Wagen]

This is awesome.

Agreed!

[chop_suey]

any more of the 65 vette?

[mrsleeve]

yes it is.

I thought i disliked stingrays till i saw that car.

You more than likely still do, this is not a Stingray its a Sting Ray. 63-67 was a 2 word badge 68-76 (IIRC) was the 1 word badge and the very ugly "mako shark" concept derived C3

[JRKOUPE]

I love both stock early vettes and modded as well....


...but fock that vette is just badass w/o being too much. The flares are simply sex...omfg.

and its show and GO..

http://www.youtube.com/watch?v=eL1WLWueWn0

[ohthejosh]

Even though this is shopped, its sooooo nice to look at!

[Deltron Dirty30]

any more of the 65 vette?

google "Brian Hobaugh 1965 Corvette"

You more than likely still do, this is not a Stingray its a Sting Ray. 63-67 was a 2 word badge 68-76 (IIRC) was the 1 word badge and the very ugly "mako shark" concept derived C3

ahhh gotcha. thanks for the info.

btw is this a sting ray?

Even though this is shopped, its sooooo nice to look at!

no Photoshop work on that trust me.

[Peterkaczynski]

Deltron I can never see any photos you post on my phone wtf mate