what rotors on Massive street kit?

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Artful Dodger
    replied
    Originally posted by JRKOUPE
    good to hear.......

    a bit ot....but are you using 12 mm thick pads in those wilwoods?......how much longer did they last w/ cooling added? I get like 5 days or so on my pads.
    I dont have a great comparison. First weekend I had the Wilwoods, I ran it at Mid-Ohio with a 2nd driver. so, we ran the car twice as much as I do on a normal weekend. Also it was a 3 day event. In that weekend, with brand new Wilwood Polymatrix A pads, we went all the way to the metal and had to end last session early due to this.

    Then I did 5 weekends of 1 driver on a set of Hawk DTC-60.

    Now I have done 2 events on my DTC-60s and they show nearly no wear.

    I am running the .480 thick pads. I use these with an aluminum backing spacer to make up the difference in caliper width vs rotor width. (the rotor is only 22mm new and the caliper is designed for a 25.4mm rotor. I felt that the pistons were running out of travel).

    If anyone is interested, I have a couple of sets of brackets to mount the wilwoods to e30 spindle and 2 sets of used rotors I need to sell. rotors are Brembo blank, corrado rotors with the center turned to fit the hub.

    Leave a comment:


  • robgoesvroom
    replied
    Originally posted by JRKOUPE
    well, on my stock oe brakes my brembos rocked....for a long time...prolly like 10 days...40 sessions....maybe more

    give us more info.....how many days on them..how old etc etc etc

    .....any rotor can crack....eventually.
    probably 6 track days and a lot of street miles over the course of 7 months

    Leave a comment:


  • craz azn
    replied
    Originally posted by robgoesvroom
    these are stock E30 brembo blanks


    Haha, I had the same thing happen to one of my rotors this past summer!

    Leave a comment:


  • Navarone
    replied
    Clearly you should have pressed both NOS buttons.

    @2:03

    Leave a comment:


  • JRKOUPE
    replied
    Originally posted by robgoesvroom
    these are stock E30 brembo blanks


    well, on my stock oe brakes my brembos rocked....for a long time...prolly like 10 days...40 sessions....maybe more

    give us more info.....how many days on them..how old etc etc etc

    .....any rotor can crack....eventually.
    Last edited by JRKOUPE; 12-13-2014, 01:02 PM.

    Leave a comment:


  • JRKOUPE
    replied
    Originally posted by Artful Dodger
    First, I do not have a Massive Brakes kit.

    But I do have Brembo Blank Corrado Rotors with Wilwood Calipers. I use Hawk DTC-60 pads on my S52 swapped e30 DD/Track car. Car is 2620lbs.

    I ran this setup with no cooling at 4 different tracks on 8 or so different weekends. I had no issues with the rotors. I did go through pads though. After running my pads all the way to the metal and trying to "cookie cutter" the backing plate of the pad, I did change my rotors to a new set of corrado rotors.

    The next year, I added cooling ducts. The pad life has gone up and rotors are still fine.

    I would think to have a catastrophic failure such as the picture, you would have to have alot of flex in the wheel bearing and when the brakes are applied, it is warping the rotor to failure. Just my opinion though.

    I drive my car like I dont care and it has been fine.

    good to hear.......

    a bit ot....but are you using 12 mm thick pads in those wilwoods?......how much longer did they last w/ cooling added? I get like 5 days or so on my pads.

    Leave a comment:


  • robgoesvroom
    replied
    these are stock E30 brembo blanks


    Leave a comment:


  • Artful Dodger
    replied
    First, I do not have a Massive Brakes kit.

    But I do have Brembo Blank Corrado Rotors with Wilwood Calipers. I use Hawk DTC-60 pads on my S52 swapped e30 DD/Track car. Car is 2620lbs.

    I ran this setup with no cooling at 4 different tracks on 8 or so different weekends. I had no issues with the rotors. I did go through pads though. After running my pads all the way to the metal and trying to "cookie cutter" the backing plate of the pad, I did change my rotors to a new set of corrado rotors.

    The next year, I added cooling ducts. The pad life has gone up and rotors are still fine.

    I would think to have a catastrophic failure such as the picture, you would have to have alot of flex in the wheel bearing and when the brakes are applied, it is warping the rotor to failure. Just my opinion though.

    I drive my car like I dont care and it has been fine.

    Leave a comment:


  • dude8383
    replied
    Yeh, Meyle rotors.

    Leave a comment:


  • JRKOUPE
    replied
    Originally posted by nyChris
    I have Meyle Corrado rotors, and they are 1 piece with no "holes" in the hat area.
    yup...... meyle may be the desired brand for moi.

    who was your source?

    Leave a comment:


  • nyChris
    replied
    I have Meyle Corrado rotors, and they are 1 piece with no "holes" in the hat area.

    Leave a comment:


  • JRKOUPE
    replied
    D...that brand does not appear to have the holes cast into the hat area....hmmm...

    Leave a comment:


  • dude8383
    replied
    I completely forgot that I took pics of my own G60 rotors when I ran them:





    I forget how many sessions I got out of them but it was at least 3-4 track days.

    Leave a comment:


  • roguetoaster
    replied
    Originally posted by JRKOUPE
    hey fellas.....all responses are appreciated but u may be missing the point.

    There have been a few issues w/ brembo and ate re rotors cracking/failing on CORRADO replacement rotors....

    its not related to brembo or ate on any other applications.

    I ran both brands on oe e 30 set ups for years and loved them!...


    Im asking re corrado application which in this scenario is used on a bbk

    back to normal programming.
    Ah, gotcha. Anecdotal at best, but in Chump the only team that I encountered that ran a Corrado didn't seem to have any cracks in their rotors after 7 hours of (not constant) running. When I asked them about the brakes (because I noticed the weird rotors) they said they never had issues with the Brembo blanks and the rotors were not visibly cracked. This was at WGI IIRC.

    Edit:

    Won't standard A2 Golf/GTI brakes work? Same size I believe, not 100% on hat offset/height. If not I think I remember from my VW days that G60 Golfs and maybe Syncros used the same brakes as the Corrado but without the hat vents.

    Leave a comment:


  • ThatOneEuroE30
    replied
    Originally posted by dude8383
    The corrado rotor is utilized with this kit. The center bore is made slightly larger to work on our cars.

    Ahhh I did not know that. Oops nvm then.

    Leave a comment:

Working...