s38b35 partout and tons of parts

[imaiami]

SUPER PRICE DROP TO GET ALL THIS GONE

-Bmw s38 b35 shortblock ……complete with pistons/ rods/ crank or each sold as pieces
Cylinder 2 piston chipped a piece off, so that piston needs to be replaced. The cylinder walls look fine
Complete 500.00 now 300




-S38b36 e34 oil pan with notch cut into it to clear e36steering rack
pan 200.00, NOW 100

-sachs clutch….clutch disc worn about 2/3
50.00 NOW 20.00


-s38 starter
50.00 NOW 20.00

-assorted p/s pulleys etc… OFFER

-s38b35 headers

100.00 NOW 50

_e28m5 engine brackets
50.00 NOW 20

-b35 distributor
50.00 NOW 20
-alt/ p/s s38 brackets
20.00 ?????


-s38 alternator
75.00 NOW 30

-s38 timing chain tensioner
50.00 NOW 15

-Innovate lc1 and xd16 guage setup with 3x wideband sensors
200.00 NOW 120

-s38b35 exhaust cam
150.00 NOW 100
-metric mechanics intake cam 290deg with 11.7mm lift
300.00 NOW 175 (THIS WAS A 1000.00 CAM)
-s38b35 cam carrier in decent condition. A bit of bearing wear as shown in pictures

250.00 NOW 120
-s38b35 cam gears
100.00 NOW 20.00 EA
Eatom m60 supercharger


150.00 NOW 75
_s38b35 head complete with valves / springs/ retainers
600.00 NOW 400
the head is good minus cylinder 2 with a bit of scoring from the piston that chipped off a piece. Also the previous owner bolted the head down without using the washers for the head bolts, so while removing the head a bit of material pulled. The top of the head bolts have a taper that normally is surrounded by the washers, but since the washer wasn’t used the alum compressed around the indent. There doesn’t appear to be any cracking or issues when I installed the head with washers.
It looks like cylinder 2 intake valve num 2 might have been bent slightly, but I have 3 extra good intake valves and 1 exhaust valve included along with valve stem seals.









-oil filter housing
50.00 NOW 20


SOLD-s38 valve adjustment shims (fiat and bmw mixed) with tons of extra shims
SOLD -s38 valve depressor tool
SOLD_ oil cooler
SOLD-remote thermostat housing w/ washers rather than thermostat inside
SOLD-s38b35 water manifold
SOLD-ms2 v3, waste spark, engine harness, all sensors, coils, injectors, ready to drop in n run s38
SOLD S38b35 intake plenum cut and welded for a supercharger mounted to it
SOLD-s38b36 60-2 crank pulley/ harmonic balancer
SOLD- adapter from s38 8 bolt to 3 bolt 6 ribbed serp belt pulley
SOLD-Uni individual filters, one with a tear in it
SOLD-S38 individual throttle bodies
SOLD-Throttle body stacks/ trumpets x6
SOLD-s38b36 headers (cut a bit to make em fit into e36)
SOLD--Getrag 280 5 speed trans….synchros had gotten a bit sticky into 2nd and third…but shifts fine if not super rushed…
SOLD-e36 bmw nardi steering wheel
SOLD-single mass chromo flywheel

[imaiami]

bumpercars

[shadow8450]

PM sent!

[ThatOneEuroE30]

Them itbs are very tempting

[b1800e30m3]

I am interested in the valve shims, depressor tool and the oil cooler with lines, don't need the filter housing. ill Pm you too and hopefully we will make something work.

Thanks,
Barry

[Good & Tight]

I am interested in the valve shims, depressor tool and the oil cooler with lines, don't need the filter housing. ill Pm you too and hopefully we will make something work.

Thanks,
Barry

I'm interested in the oil filter housing.

[imaiami]

All Pm's should be responded to n
Updated the list with all that was sold.

[imaiami]

still holdin, list is all up to date

[efficient]

Will the e36 steering wheel fit a e30?

[efficient]

bump for a good seller

[imaiami]

updated once again.....come buy this stuff. I want it gone :d

[imaiami]

OBO, come get this stufff....

[imaiami]

still got it, need it gone for cheap

[imaiami]

Super price drop

[pandaboo911]

Innovate LC1 for 120 shipped to 94087?