iS SPLITTERS!!! $80 Shipped with Hardware.

[M3 Ryan]

ryan, when can we expect production and delivery?

As stated in my first post, I will start shipping these out around Feb 2nd. They will go out in the order they were paid for, via USPS prioriety or UPS Ground.

[cactusjacks1]

Paypal sent

[JoeyJoeJ0]

Ryan will you still be making these after you move? I live in SB, so if it comes down to it id rather just meet up with you and give you 80 bucks and pick it up.

[M3 Ryan]

Yea, just e-mail me and we can meet up. I will still make them after I move but it could be a while. I bought enough plastic to produce 30 of them, and I figure I will sell around 20 in this GB. I want to make the last 10 to have in stock when people want them, as it will be at least 3-6mo before I get a chance to make more. Where u at in SB? I am out in Winchester Canyon...

[King Luis]

YAY!!!! few more days...i should do some repair to my lip and repaint it. :p

[mazur]

Do these offer any significant downforce?

[BDSax]

Do these offer any significant downforce?

you need a huge metal ricer spoiler for downforce! j.k

that is a good question

[parkerbink]

Here b mine.

[M3 Ryan]

Hey guys--
To answer your question about downforce, they do offer *some* downforce. They have been known to rip the iS lip off at 100+ mph, so I advise all of you to get new clips for the lip and to use a few zip ties along the front and ends of the spoiler to the valance to help hold onto the lip.
I have the first 10 splitters cut, I need to shape them and pack them, which I should have all 10 done before 5pm friday, so they will ship out friday afternoon. I have 18 sold so far. I will be doing another batch on saturday (if all goes well) and everyone should have their splitter shipped out before Friday Feb 9th. I will not be able to make the M-Tech 2 splitters for a little while longer until I get my car back, so those of you waiting on those will need to wait just a bit longer.

[mscott]

pm sent

[RCWells]

Hey guys--
To answer your question about downforce, they do offer *some* downforce. They have been known to rip the iS lip off at 100+ mph, so I advise all of you to get new clips for the lip and to use a few zip ties along the front and ends of the spoiler to the valance to help hold onto the lip.

With just the factory clips, mine has held up fine at speeds up to 130mph, however, individual results may vary so you may want to follow the manufacturer's guidelines for installation. ;)

[M3 Ryan]

With just the factory clips, mine has held up fine at speeds up to 130mph, however, individual results may vary so you may want to follow the manufacturer's guidelines for installation. ;)

That is impressive... I have had many customers tell me that even one short burst up to 90mph ripped it off. One of them went back to get the splitter but it had been run over by a truck... The splitter was fine, but the iS lip was broken into about 6 peices... The iS lip will break before the splitter does... I just tell people to zip tie it to be safe. Also, you can't see them from the outside and the chance of someone stealing it is less likely. You can simply pull the lip off the car, but when it is zip tied 10 times, it takes a lot more than just a gentle tug to remove it...

[MR 325]

Mine held up just fine at 145-150ish on the old car.

[Mtriple]

Mine held up just fine at 145-150ish on the old car.

+1

[e30bimmerdude]

Payment sent! I forgot to list me Member Name, so it will come in as Troy Apro... thanks and thats 1 early splitter