I guess I should finally post something, doing a m50 swap soon

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • ExViTermini
    replied
    Winner winner chicken dinner! :up:

    Leave a comment:


  • 2poor2tune
    replied
    damnnnn i got lucky today. the only e36 in the junk yard and it has a non vanos motor with harness and ecm just waiting for me to pull it. here all that i got for 75 bucks

    engine harness, matching ecm, the correct oil cap, e36 engine bracket arms, little elbow off the throttle body, and thermostat housing that i needed.



    Uploaded with ImageShack.us

    Leave a comment:


  • 2poor2tune
    replied
    well since i am an idiot and hacked the harness that i was supposed to keep i have no idea what goes where. im gonna pick up a harness off of someone here soon but im pretty sure it wont be to hard to figure out which clip goes where. we will see though. thanks for the advice guys. going to get a new valve cover gasket and my e36 arms today. maybe order my e28 mounts too.

    Leave a comment:


  • Jand3rson
    replied
    Originally posted by e30s50dan
    ....and take notes and photos,for your next swap.....there will be one;)
    Yes, dear god. Take pictures, notes, and label the shit out of everything. I wish I had done even half of that.

    Leave a comment:


  • 2poor2tune
    replied
    here is the head, looks pretty clean


    Uploaded with ImageShack.us

    is it normal to have the tensioner pop up and down as you turn the crank? the one between the intake and exhaust cam


    Uploaded with ImageShack.us

    Leave a comment:


  • 2poor2tune
    replied
    I think that auto mod is done in the cab and to the chassis harness. I have done it once before on my old 90 325i.

    I pulled my valve cover off today to find a pretty damn clean head. I'm hoping the rest of the engine is as healthy head looks. It seems as if the previous owner never replaced the valve cover gasket. It was rock hard and the spark plug holes were halfway filled with oil. Valve cover gasket will be bought tomorrow
    also the tranny will be mounted. I already modified the e34 oil pan to fit the stock m20 single mass flywheel

    Leave a comment:


  • greyis89
    replied
    If you're using an ecu out of an auto car there's some mod you have to do to override neutral saftey I think but don't know what off hand. The wiring harness can be looked up depending on year car and engine. There's slight color differences but it's not bad.

    Leave a comment:


  • 2poor2tune
    replied
    Originally posted by e30s50dan
    ....and take notes and photos,for your next swap.....there will be one;)
    s50/52 perhaps????? i hope so

    Leave a comment:


  • e30s50dan
    replied
    ....and take notes and photos,for your next swap.....there will be one;)

    Leave a comment:


  • Knoepfler
    replied
    be patient and don't get too frustrated

    Leave a comment:


  • 2poor2tune
    replied
    The car I am pulling the motor out of has a silver label idk the numbers yet or if its a vanos motor. Ill have to check when I go back. I couldn't make it today

    Leave a comment:


  • e30rapidic
    replied
    Originally posted by 2poor2tune
    sounds good. What harness/ecu are you using?

    413 red label and auto e34 vanos.

    Leave a comment:


  • 2poor2tune
    replied
    haha played out is good for me, that means most people have already ran into all the issues. Im gonna have lots of fun with it for sure. I will have to post up everything else I have done to the car so far soon. I wanna get the engine in the bay before posting it up though.

    Ill try not to be to annoying with the questions but the wiring still worries me. The rest I think I have under control thanks to this site and google
    Last edited by 2poor2tune; 03-14-2011, 04:47 PM.

    Leave a comment:


  • Jand3rson
    replied
    M50 swaps are so played out.

    ;)

    If the valve cover is just squared off at the front, it's a non-vanos. If it has a kind of round "bulge" at the front, it's Vanos, and that's the Vanos unit.

    Awesome to see another swap, I've had so much fun with mine so far. There's tons of great info all over this place, some of it can be a little hard to find at times. Don't be afraid to ask questions, but please, search for what you can before you just start posting threads for every question. I'm more than happy to answer anything I can, and so are most of the others that have done 24V swaps.

    Leave a comment:


  • 2poor2tune
    replied
    Originally posted by Lawson509
    Get a porsche 944 booster. It will save you lots of time and effort.
    noted and than you very much

    Originally posted by e30rapidic
    awesome...we can compare notes as I am doing my S50 install right now
    sounds good. What harness/ecu are you using?

    Leave a comment:

Working...