FYI - some N52 oil pan research

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • trackjunkie21
    replied
    Originally posted by gpak31
    what are you going to use as motor mounts, i have an parts e30 and the n52 for test fitment
    I'm sure the fitment is actually the "easy" part of the swap, Can't imagine what needs to be done electronically wise.

    Leave a comment:


  • gpak31
    replied
    what are you going to use as motor mounts, i have an parts e30 and the n52 for test fitment

    Leave a comment:


  • VinniE30
    replied
    Nice looking ports. I bet it flows well since the power doesn't drop off till after 7k.

    Is this going in an e30? Please tell me it is.

    Leave a comment:


  • hoveringuy
    replied
    Thanks!

    I had asked him to post some pictures of his N52 head because I have heard that the ports are CNC'd like the S54.

    S54 Intake port = 275 CFM

    M54 Intake port = 200 CFM


    N52 = ??

    M54 "D" port heads for comparison, 50x27mm. I've heard that in order to make the M54 intake flow well material needs to be added to them, they're TOO open.



    Wangan's S54:

    Attached Files
    Last edited by hoveringuy; 02-22-2012, 08:13 PM.

    Leave a comment:


  • gpak31
    replied
    sorry for the crappy iphone pics, camera batteries charging











    Leave a comment:


  • VinniE30
    replied
    Another FYI:
    The transmissions are compatible with the rest of the older 3 series transmissions.
    To clarify, according to parts diagrams, it uses the same 6 speed ZF trans that the later e46's used.. which as we know will bolt up to any of the e46 and e36 24v engines and also the m20. So theoretically, you could use a g260 with this engine.(it would bolt up atleast)

    Leave a comment:


  • hoveringuy
    replied
    Bent rods will do that, but I've also heard the N52 pistons aren't that great and will cause it normally.

    Also, how far does the use of aluminum bolts go? Head bolts? Transmission mounting bolts? Are there any steel bolts?

    Leave a comment:


  • gpak31
    replied
    no no no, the car sucked in water, bent 2 rods, car ran normal, didnt find out about the
    bent rods till i removed the head and saw that cylinder 2 at tdc was sitting lower in the cylinder, then removed engine and oil pan and saw cyl 2 and 5 had bent rods

    Leave a comment:


  • hoveringuy
    replied
    Originally posted by gpak31
    no ran fine no faults, high oil consumption was the complaint for the engine
    High oil consumption bent 2 rods? If nothing else I may be interested in the block/oil pan to see if it fits (if you can't check that..)

    Leave a comment:


  • gpak31
    replied
    no ran fine no faults, high oil consumption was the complaint for the engine

    Leave a comment:


  • 328ijunkie
    replied
    Low/no oil pressure?

    Leave a comment:


  • gpak31
    replied
    if anyone is interesteed i have an n52 from a 528xi, 2 rods are bent, possible use for mockup, also have a brand new head, headgasket, headbolts, and intake manifold
    and a bunch of accessories

    pm if interested

    Leave a comment:


  • 328ijunkie
    replied
    Whats up with that dyno you just posted. That dood needs a tune... ~15 A/F!?

    Leave a comment:


  • VinniE30
    replied
    I think the N52 could get to 300HP (crank) with better airbox/filter, headers with full exhaust, and tuned on a dyno.

    Leave a comment:


  • hoveringuy
    replied
    Originally posted by JGood
    What N52 is that? Isn't there like 5 different version of that engine in various models? Are all US cars 3.0 liter?
    It's a motor that someone converted from the 2.5 specs to 3.0

    All US N52's are 3.0 litres, even the 2.5 versions. The difference in the 2.5 is a crappier 2 stage intake and detuned software. I'm guessing that the magnesium/aluminum block production process couldn't be economically duplicated in two sizes.

    The best N52 version is rated at around 268 bhp which would be around 215whp. Makes sense.

    I do appreciate the light weight and great torque my M54 has and I imagine the N52 would be even better.

    Leave a comment:

Working...