Announcement
Collapse
No announcement yet.
How to replicate HELLA's smoked ellipsoid technique:
Collapse
X
-
My brother did mine this weekend using a space heater to open them up, then he froze the silicone sealant before taking it off. They look great. I used the machined xhairs from turk in the X pattern rather than the +
-
Originally posted by BrewCity11 View PostReally? Check out post #17 and 18. http://www.e30tech.com/forum/showthread.php?t=52494
Not doubting you, but correct info would be nice, regardless who's right.
EDIT: i just tried again today and same thing happened, the reflector has a different depth, so the sides dont align. i wish i would have kept my busted up high beam housing, i could have just cut it in half and copied the profile.Last edited by straight6pwr; 02-18-2009, 12:26 PM.
Leave a comment:
-
Originally posted by straight6pwr View Posteuro cross hairs DO NOT fit in u.s. high beams. NOT EVEN CLOSE. you'll have to make your own, and its fairly easy. not sure if depo's shape is based of the euros or the u.s.
Not doubting you, but correct info would be nice, regardless who's right.
Leave a comment:
-
euro cross hairs DO NOT fit in u.s. high beams. NOT EVEN CLOSE. you'll have to make your own, and its fairly easy. not sure if depo's shape is based of the euros or the u.s.
Leave a comment:
-
^ i have a high beam for you that has the lens already off of it, but you'll have to buy the other one and two low beams with it:)
Leave a comment:
-
someone in another thread suggested a heat gun, maybe you can try that next time
Leave a comment:
-
Is it just me or does this crosshair template not fit U.S. hella high beams? I cut it out over and over and it just didn't fit in the high beam?? Ah well I spent about an hour and came up with my own template (admittedly not perfect..)
Oh and I'm 0 and 2 on boiling the high beams to get the lenses off, busted them both. And unfortunately our oven is broken. :( The low beams were much easier.
Leave a comment:
-
ok guys, the guy making them actually adapted the pattern to better fit his headlights... which means he ran off a set that properly fit DOT/9006 high beams. he didn't realize the the bowls are differently shaped because of different bulb type and regulations.
Hoping he still has the pattern for the ECEs to run off which I would need, but I thought I'd let y'all know that if you have DOT highs, you can now join the 'fun' and pick up the first crosshair set designed to properly fit them.
They are run off and ready to ship on BF.C
Leave a comment:
-
So, I baked my low beams and got the lenses of but this plastic piece melted to shit on one of them. Any idea what it's for and if I need to replace it?
Thanks.
Leave a comment:
-
Originally posted by Kingb View PostAnybody have or can get some more made?? I know that there are more people interested to do another group buy on these.
Also for all of you that have broken yours and need another set I have access to plenty of Euro smileys. Just hit me up.
right now we have about 20 members signed up for them.
Leave a comment:
-
Originally posted by BigSam View PostI honestly found it easier to boil the lens assembly. I put it in the water, and turned the heat on. I let them sit until they boiled, then for about 5 more minutes. Try prying up a little bit, then put them back in the water for like 5-10 more minutes. Very time consuming, but I didn't break a single lense. I also used the 'X' patern, I found it easy to line up to make the slots in the plastic backing. Uou can also use a razor knife to cut the adhesive, that works in tight spots.
PS, try using differnt color adhesives, I used red and it came out looking like my car was stoned, but awesome at the same time.
Sam
Leave a comment:
Leave a comment: