Ideal Megasquirt Setup

[whodwho]

30# should work at that psi, I get about 90% duty at 10psi @ 12.5 - 12 afr

[dave.a.cote]

My wife bought me an Eaton M-62 supercharger for my birthday - is that cool or what?

Swift - I was thinking I would need something in the high 30, maybe 40lb to run ~6 or 7 psi boost.

[nando]

Do you have plans for boost?

no immediate plans, but should I decide to later, I don't have to worry about my injector size too much. :)

I'd think 24# should be plenty for most N/A setups.

[SwiftE30]

1. Unless you or your tuner have tuned a VANOS motor before, don't waste your time and money on MS. Spend the cash and get a tried and true tune from someone like TRM. Drive-ability will be much better across the board, and will allow you to take advantage of VANOS.

2. That injector size will be too small for a gt35r or gt40.

Do some research on bimmerforums' Forced Induction section, there's all you need to know there. ;)

http://forums.bimmerforums.com/forum...play.php?f=150

What size injector do you think will be big enough?

[dave.a.cote]

Do you have plans for boost?

[nando]

M20B28

the injectors are probably about double what I "need". Max duty cycle is somewhere around 40-45%. But having large injectors means I can more easily control the PW at high loads, so it's a bit of a trade off.

[dave.a.cote]

nando, what is your engine configuration?

[nando]

I like this. Not that much money and seems like an awesome setup.I'll look into that combo more. THanks. What size injectors are you using?

I'm using 42#, but it doesn't really matter that much with standalone. Although you don't want to go too big because idle pulsewidths will be too small and it will be harder to tune at low loads, 24# are probably plenty. 42# have been fine for my engine though, I got them because they were basically brand new and a friend gave me a good deal.

[dave.a.cote]

I am using 24lb injectors with a 3.0 bar FPR. I am also running an Innovate LC-1 and to get AFR's in the 12.5 range at 6k rpm, I am seeing about 80% duty cycle and an outside temperature near freezing.

I tried to build it on a budget. I am using dual intake cams, ebay headers with dual 2" exhaust, m20 single mass flywheel. I am hoping to be around 210 hp at the wheels.

[mikeday]

Im selling my megasquirt and pnp adapter board...

You should buy it ;)

[SwiftE30]

http://www.r3vlimited.com/board/showthread.php?t=181166

MS2 is almost a downgrade from the stock computer - batch fire, although you can do COP, and it's much easier to tune and it can do other stuff the stock computer can't (boost control, launch control, etc).

I think for the price difference MS3 is the way to go. $365 for the V3.0 kit, add $90 for the MS3x sequential board and you've got a pretty complete system for not that much money.

I like this. Not that much money and seems like an awesome setup.I'll look into that combo more. THanks. What size injectors are you using?

[SwiftE30]

1. Unless you or your tuner have tuned a VANOS motor before, don't waste your time and money on MS. Spend the cash and get a tried and true tune from someone like TRM. Drive-ability will be much better across the board, and will allow you to take advantage of VANOS.

2. That injector size will be too small for a gt35r or gt40.

Do some research on bimmerforums' Forced Induction section, there's all you need to know there. ;)

http://forums.bimmerforums.com/forum...play.php?f=150

You gotta be able to start somewhere. Thats the whole point of restoring a car in my opinion. I would rather learn how to do it rather than letting someone else do it.

[nando]

dude, single vanos motors are ON-OFF-ON, based on RPM/Load. it's not rocket science.

boost has nothing to do with it. You basically want to set the cam timing for the highest torque at that load site. at lower loads you might compromise to make it a bit smoother.

and i've seen plenty of stock ECU motors with huge torque dips at the vanos switchover point. So just because it's a stock tuned ECU doesn't mean it's smooth. Whoever is tuning it still has to know what they are doing. the hardware is irrelevant.

infinitely variable double vanos is a little more difficult, but certainly not impossible. and that's not what we are talking about, anyway.

[e30polak]

MS3 can easily control VANOS.. but whatever.

Never said it couldn't, but very few tuners are able to tune the VANOS motor as smoothly as the stock ecu allows. Things get even worse under boost.

Don't bother with anything less than the latest and greatest megasquirt.

Or get a proper tune from us. :)

This.

After driving multiple turbo cars, I've never seen such smooth drive-ability as those tuned by TRM.

[matt]

Don't bother with anything less than the latest and greatest megasquirt.

Or get a proper tune from us. :)