Does anyone make a Feed/Drain oil line kit?

[Mr. Burns]

instead of piecing each fitting one by one, i'm hoping that someone out there has a ready to buy kit that offers everything pre-measured up with -3an/-4an fittings.

*edit* for M20b25 engine, t3/t4 turbo .63AR
anything?

*searched, no dice.

[Cyrix2k]

check ebay. You'll still need to have a fitting welded into your pan or tap the block.

[JCarp90]

I searched and searched. Never found one.

[The Humjet]

http://www.e30tech.com/forum/showthread.php?t=74816

Check out Jordan's turbo thread on e30tech, I like his oil feed setup. He also gives part numbers so its easy to chase up what parts he used.

[Cyrix2k]

I searched and searched. Never found one.

http://www.ebay.com/sch/i.html?_nkw=oil+feed++drain+kit&_sacat=0&_odkw=oil+feed+and+drain+kit&_osacat=0

I'm using something like this one

http://www.ebay.com/itm/36-4-AN-1-8-NPT-OIL-FEED-FITTING-LINE-17-10-AN-TURBO-OIL-RETURN-DRAIN-LINE-KIT-/230695735008?pt=Motors_Car_Truck_Parts_Accessories&hash=item35b6898ee0&vxp=mtr#ht_2666wt_1396

You still need a couple extra parts, but not much. On the m20, I used an oil filter sandwich adapter.

[blueapplesoda]

I posted this to Mr. burns ia PM, but thought I'd like to share what I use in my oil feed/drain kits. I don't actively sell them because my margin is basically zero for this kind of stuff, but if you need it I can get a hold of all the parts to take care of you.

All that's needed is that I need to know what your engine, manifold, and turbo are to give you a correct kit. The base kit (bare minimum, without oil drain flange) is $120 plus 8.95 flat rate for shipping, depending on what parts you need.

Comes with:
27.50 - 3an stainless feed line
34.95 - oil pressure adapter
4.95 - turbo oil feed adapter (depends on turbo)
13.90 - 2x 8/10an pushlock fittings
15.00 - 2 ft 8/10an aeroquip drain hose
8.00 - 1 ft 8/10an firesleeve
12.00 - 8/10an 45/90/180 bulkhead
2.45 - 8/10an lock nut
1.25 - 2x 8/10an bonded washers
-----
120.00 - turbo oil kit, minus drain flange.

Optional:
30.00 - turbo oil drain flange, gasket, and hardware (depends on turbo). 8an or 10an

For top mounted turbo's, sometime the drain is too close to the manifold/flange or turbine housing, and the provided fire sleeve is not enough. Usually with Garrett/replica GT turbos I have encountered this issue with. I have an extension kit that will extend the turbo oil drain
with a 8an or 10an stainless steel hard line. Drain extension kit some with:

45.00 - 6" 8/10an stainless hard line
5.00 - 8/10an union (male-male)

I also have water lines kit for watercooled gt turbos.

35.00 - 2x 14mm extended banjos with 45 degree bends
15.00 - 2x 14mm banjo bolts
2.00 - 4x 14mm sealing washers
9.00 - 4x ABA hose clamps
20.00 - 8ft 5/16 hose

Thanks!

Derek
DedericMS

[BMWZ318is]

i found mine on ebay thats my best guess unless you have a performance shop near by that keep that stuff in stock

[Mr. Burns]

Thanks everyone, and Derek PM returned

[MF DOOM]

http://www.siliconeintakes.com/index.php?cPath=17&osCsid=654b55e49ba936cac7e6dc7d687d3d31

[Cyrix2k]

I'll vouch for silicone intakes - I ordered silicone couplers from them and they came quickly. Their stuff it pretty good quality too.

[custom e30]

i turned my check oil tub into a bong, so down at the bottom it, return line runs around the front of the engine to the bottom of the tube,