M20 3.0 stroker build - looking for advice from the M20 gurus

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • dranik182
    Noobie
    • Nov 2026
    • 1

    #1

    M20 3.0 stroker build - looking for advice from the M20 gurus

    Hi all,

    I'm planning an N/A M20 stroker and would really value advice from the M20 gurus here. I have quite a bit of engine building experience, but I'm new to the M20 and its quirks, so I'd rather learn from people who know these engines well.

    The build so far:

    • 85 mm bore (unless you'd recommend otherwise)
    • M54B30 crank, 89.6 mm stroke
    • OEM BMW 135 mm rods
    • Custom forged pistons (4032 preferably)
    • 885 head, to be ported.
    • 325i intake manifold (port matched to the head)

    The car: E28 that already runs a SETA 2.7 with 885 head built by Bimmerheads and their 274 cam, all other 325i parts, Motronic 1.3. Getrag 260 + Z3 3.46 torsen diff. And it's not a daily driver - 1000 miles a year at best.


    The goal: I want the engine to keep pulling all the way to the limiter, and I'm fine giving up some low end to get there.


    Questions:

    1. Block. I'm buying a core engine tomorrow and have two options: a 1987 ETA with 885 head(manual), or a 325i(auto) engine of unknown year. From what I've found, the 325i block deck height is 206.7 mm, and the ETA is either 206.2 or 206.7 mm. Which block would you choose for this build? My thoughts are - a low-revving ETA engine could have a head in better shape, but 325i with auto could be less abused and more parts can be used from it.
    2. CR. BimmerHeads advised against going over 10:1, but I see plenty of builds at 10.5 or even 11:1. I'll most likely run 91 octane (California). What would you target?
    3. Pistons. How much better is a OEM domed/dished crown shaped to the chamber than a flat top? From my research, JE offers the shaped crown and CP and MM(Wiseco) does flat tops. Please correct me if that's wrong. Also, when ordering custom pistons, where should they sit relative to the deck at TDC: slightly below, slightly above, or flush?
    4. Head. I've talked to BimmerHeads about porting. 600$ sounds reasonable. Who else should I consider? 5150 cnc porting costs 1500$ plus shipping which is a bit too much for me but if this is essential I might do it.
    5. Camshaft. This is where I get lost. Which cam would you pick for a top-end bias with a smooth, linear power curve? I understand static CR is one thing and dynamic CR depends heavily on the cam, so the cam and the CR have to be chosen together. I'm fine with a slightly lumpy idle, but I don't want a full blown hot rod cam. Any combos you've had good results with?
    6. Valves. Do I need oversized valves, or is a good multi-angle valve job enough at this level?
    7. Valve springs. Are the stock 325i dual springs good enough, or should I go to single springs as Metric Mechanic recommends - their explanation looks very reasonable.
    8. Exhaust. Are headers worth it, or do the stock manifolds flow enough? Right now I have 325i manifolds into a dual pipe with a resonator and a muffler.
    9. Engine management. Can stock Motronic 1.3 with a tuned chip handle this setup, or do I need a standalone? I've seen plug-and-play options that use the factory harness and add a wideband, knock sensor and maf. What are people using, and is it worth it?
    10. Power. Can I touch 200whp with it or what's your estimate?

    One more note: ITBs are a bit outside my budget for now. As I understand it, they add roughly $2,500–3,000 to the build.

    To thank you for your help, I'll document the whole build here with photos and post dyno results when it's done.

    Thanks in advance!​
  • digger
    R3V OG
    • Nov 2005
    • 6207

    #2
    I have built a 3.1 L stroker with the stock intake and tried to extend its rev range through camshaft selection. In my opinion (my option has changed), this is not a good approach as the total combination is mismatched, and I would not recommend it for the following reasons:
    • The increased stroke and bore push the induction system beyond its effective capability.
    • The intake length is tuned for midrange performance.
    • Using an aggressive cam to force the engine to rev significantly above its natural operating range reduces torque at an rpm where the engine really should be most efficient. It also requires a high compression ratio and really calls for 93-octane fuel, it is also not well suited to Motronic.


    The result is usually a more expensive setup that performs no better than a milder combination. Extra displacement adds little power when the engine is heavily restricted: it tends to produce more torque all else equal; but not more power as it is choked. Often milder engines make the same power as typical 3L strokers but needs a bit more revs to do so and because all the parts work together it really is better option in most circumstances. Dont fall into the trap that since it requires no extra expense to use the 89.6mm crank that it is the best option

    In my opinion, a more balanced OEM+ combination is a better choice—for example, a 2.8L or 2.9L engine with a mild cam. Think of a slightly improved Alpina 2.7L, rather than trying to make a big leap and trying to make the engine something it is not. A smaller engine will naturally peak at hp rpm so might have better characteristics.

    Alternatively, build a 3.0 L engine with parts that complement its natural strengths: i.e. optimise for low-end and midrange performance, rather than top-end power kind of like a lighter version of the M30.

    I would only pursue the higher-revving big stroker approach if you are prepared to address all the associated issues, but note that costs can quickly escalate.

    i haven't really answered any of the direct questions at this point deliberately
    Last edited by digger; Today, 07:26 PM.
    89 E30 325is Lachs Silber - currently M20B31, M20B33 in the works, stroked to the hilt...

    new build thread http://www.r3vlimited.com/board/showthread.php?t=317505

    Comment

    Working...