Any interest in B35 mounts?

[pporcaro]

i think it's badass, but i wish it would work with the b34 im thinking of buying

[Doughnut]

Nice looking brackets.

If you are swapping an m30 into an originally m40 powered e30 and you want to run A/C - you will need to have the low side A/C line extended as it is too short to reach the fitting on the compressor of the m30.

Just a FYI for you guys.

[learningcurve86]

Very nice looking mounts!

-who needs AC? (kidding...but i'm not using it - but thats because i never turn it on so i don't want to bother with it)

[Jean]

A/C is a must in CA.

[learningcurve86]

just bought a set of these... I'll be sure to post a shot of them installed :)

also- Jean: CA is one of those places I would visit but couldn't live. I would melt like an ice cube.

[Good & Tight]

just bought a set of these... I'll be sure to post a shot of them installed :)

also- Jean: CA is one of those places I would visit but couldn't live. I would melt like an ice cube.

Here are yours fresh out of the jig. Shipping them out tomorrow and will be in your hands by Wednesday.

Thanks
Otis

[884door]

Nasty welds. I can't believe anybody would pay $290 for these.

[Good & Tight]

Here is the oil pan clearance.
Also have another set ready to ship.

[Ali//325i]

I'll prolly pick up that other set. Do you think you can get me some close ups of the welds and the joints. I trust that if you are using and another member they should be okay but I just want to make sure before I buy them :) Thanks!

-Ali

[Good & Tight]

I'll prolly pick up that other set. Do you think you can get me some close ups of the welds and the joints. I trust that if you are using and another member they should be okay but I just want to make sure before I buy them :) Thanks!

-Ali

Here you go, they are ready to ship.

Paypal---- Panayiotisx2@gmail.com

[Ali//325i]

Here you go, they are ready to ship.

Paypal---- Panayiotisx2@gmail.com

Sweet man. And just to clarify a couple of things, position 2 will allow turbo/air conditioning and needs sledge hammer action to fit the motor correct?

Thanks for the close up!

-Ali

[Good & Tight]

Sweet man. And just to clarify a couple of things, position 2 will allow turbo/air conditioning and needs sledge hammer action to fit the motor correct?

Thanks for the close up!

-Ali

yes position 2 requires some hammer mods were the back of the head is. Just tap it in 1" below the brake line that's attached to the fire wall in a 8x8 area and that's it. A/C will work also.

Otis

[Ali//325i]

cool about to send paypal. What kind of paint did you use on the mounts? I am probably going to rustoleum them and paint them white so its easier to check for cracks down the road. Just didnt know if you already primed them or not.

Money sent!

-Ali

[Good & Tight]

cool about to send paypal. What kind of paint did you use on the mounts? I am probably going to rustoleum them and paint them white so its easier to check for cracks down the road. Just didnt know if you already primed them or not.

Money sent!

-Ali

It's high temp paint baked on. Got payment will ship out first thing next week and will send you the tracking #.

Thanks
Otis

[SickE30]

So, if I am reading this correctly. Pos # 2 allows a/c and turbo fitment and requires very little BFH treatment? With Pos # 1 you can run turbo and no a/c? Or no turbo @ all and a/c with no BFH treatment @ all? Thanks Otis.