the damping of the shock has ZERO effect on how low the car sits so people need to stop thinking that the shocks are adjusted incorrectly. However, if you are using shortened shocks that were shortened too much for the spring you are using then you will have an issue of coilbind like you are showing.
Other than that the issue could be caused by some ridiculous speaker box in the trunk (200lbs) or by having the incorrect springs on the car. No spring should be designed to have 4 coils touching each other.
Does this look normal to you?
Collapse
X
-
gtfo, you don't know what you're talking about. He could seriously screw something up if he "pushed it" with a faulty rear suspension.
OP-
The rear springs are easy to get to yourself. I would take one out (jack the rear up, step on the control arm a bit and pull the spring out). Try compressing it with your own strength. If it compresses somewhat easily, it could be that the springs are faulty (although I have not seen too many cases with this problem). Another thing to test while you're under there is the shock. Be sure it is mounted and also make sure the spring pads are still intact.
Really nothing any of us can do from here. You're either going to have to test it out yourself, or take it back to the shop who installed them and ask them what is going on.Leave a comment:
-
Tomorrow jack up the car and check. There should be rubber pads on top and bottom in the front and rear. People often remove them to get more of a drop though which is probably what's going on here. Go ahead and run it though, it's not unsafe or anything.Leave a comment:
-
i didnt really push the car to the limit yet i dont feel safe. hmmmLeave a comment:
-
this suspension shop that is known for many years to do great work lol.Oh I'm not saying Koni's are bad, don't get me wrong. The rear spring pads are rubber pads that go on top and bottom of the springs. They vary in thickness, but are typically about a 1/2 inch each x 2 = 1" difference in overall height right there.
After looking at that rear picture. I bet they took out all of the spring pads...front and rear. Who did the install?
so how many spring pads do i need for the rears? the front seem fine just the rears. do i need 4?Leave a comment:
-
Ya that deosnt look right. Are they both the same? What's the ride like? Even is the shocks are on the softest setting they shouldn't be that compessed. Mine are verry close but they don't all touch like that.Leave a comment:
-
Oh I'm not saying Koni's are bad, don't get me wrong. The rear spring pads are rubber pads that go on top and bottom of the springs. They vary in thickness, but are typically about a 1/2 inch each x 2 = 1" difference in overall height right there.
After looking at that rear picture. I bet they took out all of the spring pads...front and rear. Who did the install?Leave a comment:
-
oh i just got konis because they were the only ones my source could get. never knew there was a band wagon :o:D when you say stock spring pads what do you m ean?The inactive coils on the rear are in the middle. They are supposed to bind like that. I don't recall all 4 middle coils binding under the weight of the car but the end coils are the ones doing the "work". Running stock spring pads? I run Bilsteins with mine and they are great. Everyone jumped on the Koni bandwagon when GC started recommending them but I have them on my convertible with some very low springs and it feels like they are bottoming out.Leave a comment:
-
The inactive coils on the rear are in the middle. They are supposed to bind like that. I don't recall all 4 middle coils binding under the weight of the car but the end coils are the ones doing the "work". Running stock spring pads? I run Bilsteins with mine and they are great. Everyone jumped on the Koni bandwagon when GC started recommending them but I have them on my convertible with some very low springs and it feels like they are bottoming out.Leave a comment:
-
Looks like a pack of hot dogs. Pretty sure the coils should not be touching.Leave a comment:

Leave a comment: