Which way to go...BC or GC?????

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • kalib0y
    replied
    Originally posted by Cha Ching
    Ryan, where did you get your BC's?
    Got them from Nonstop tuning: http://www.nonstoptuning.com/ official sponsor of Chelsea Denofa

    Leave a comment:


  • nando
    replied
    Originally posted by ZekeTheSneak
    I have one question. How low do you want to go? Bcs will lay frame. Gcs will not and will ride like dick/blow konis once super low.
    that depends on so many factors!

    the length of your strut inserts
    how long the remaining housings are after you modify them
    the length of the springs you choose
    where you weld the perches
    stack height of your strut mounts
    bump stop length

    saying you can't go low with GC is idiotic. it will go as low as you want to build it for. blowing konis? what random chinese shit is inside the BC kit? who makes the inserts? how many people have 100,000 miles on a BC strut insert? Bueller?

    besides, if all you want is a dumped ride that "lays the frame" - it's going to handle like shit anyway (yay roll centers and camber curves!). Just take out the springs and put some 2x4s in there, it will handle about as well.

    Leave a comment:


  • ZekeTheSneak
    replied
    I have one question. How low do you want to go? Bcs will lay frame. Gcs will not and will ride like dick/blow konis once super low.

    Leave a comment:


  • nando
    replied
    hey, what do you know? shocks are just shocks, they don't have any effect on handling or ride quality at all. and apparently, you can magically remove 3" of suspension height without losing any travel. amazing!

    Leave a comment:


  • SkiFree
    replied
    Originally posted by 3rotore30
    ^ ignorance...

    out of interest, would anyone have the instructions to determine how much of the strut to remove before welding?
    nope, just wisdom.


    And I have those instructions your asking for.

    Leave a comment:


  • immajackuup
    replied
    Originally posted by FLG
    I love my BC's..:o


    Got em from http://www.circuitmotorsports.net/

    Give em a call and talk to Tristian, cost about 995? or so, whatever spring rate you want, even comes with the extenders for the rear so if you run the rear covers in your trunk you dont have to remove them to adjust dampening. Had em in about 3 days. Also they were great when it came to answering emails and phone calls...sometimes id forget and call at 8pm and he would still be there answering phones, even was going back and fourth with emails at nearly 1am in the morning.
    been talking to him about the bc kit for the pass couple days,I probably buy the bc kit from him next week instead of that group buy thing.

    Leave a comment:


  • FLG
    replied
    I love my BC's..:o


    Got em from http://www.circuitmotorsports.net/

    Give em a call and talk to Tristian, cost about 995? or so, whatever spring rate you want, even comes with the extenders for the rear so if you run the rear covers in your trunk you dont have to remove them to adjust dampening. Had em in about 3 days. Also they were great when it came to answering emails and phone calls...sometimes id forget and call at 8pm and he would still be there answering phones, even was going back and fourth with emails at nearly 1am in the morning.

    Leave a comment:


  • Cha Ching
    replied
    Originally posted by kalib0y
    I have zero problems from my BC coilovers. I loved them on my s50 e30 and currently on my LS1 M3 that I track quite often. I used to run KW V3 on all my cars but not Im all about BC. Great stuff regardless where they are made.
    Ryan, where did you get your BC's?

    Leave a comment:


  • jaywood
    replied
    Originally posted by SkiFree
    And that right there is reason enough to go with the Ground Controls.
    LOL






    You're supposed to leave 50mm of the original strut housing on there.

    Leave a comment:


  • 3rotore30
    replied
    ^ ignorance...

    out of interest, would anyone have the instructions to determine how much of the strut to remove before welding?

    Leave a comment:


  • SkiFree
    replied
    Originally posted by GCMARK
    BC makes their own dampers.

    And that right there is reason enough to go with the Ground Controls.

    Leave a comment:


  • immajackuup
    replied
    why worry about weld?? when the factory did the same thing.

    Leave a comment:


  • d_elson0
    replied
    Originally posted by jizo
    Cool video.....I kinda learned something. But now its the welding to the knuckle is where i really worried. and what shocks does BC come with? Obviously not Koni's...
    nothing to worry about, unless you weld crappy or your welder welds like crap... get someone that is confident, heat the cast, and make sure its clean.... let air cool after welding...

    If you're really tripping, you can put in extra stiffening/brackets to strengthen... I didn't, I trust my welds.

    Leave a comment:


  • DRTSRFR
    replied
    BC makes their own dampers.

    FYI: The "dual" adjustability was never intended to be what it is considered today. The bodies were threaded so they can apply any bottom mount to THE SAME DAMPER, regardless of the chassis.

    If the damper is correctly designed for the platform there's no need for dual adjustability.

    Leave a comment:


  • jizo
    replied
    Cool video.....I kinda learned something. But now its the welding to the knuckle is where i really worried. and what shocks does BC come with? Obviously not Koni's...

    Leave a comment:

Working...