Coilovers that dont have to be welded

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • jwiles
    replied
    Originally posted by mkcman17
    You're sure a cocky sonobitch. You happen to go to clemson?

    Stop being a lazy bum, buy a cutoff wheel, take off the perch and run adjusters and 5" springs. Done.

    yeah im headed that way either this fall or spring, Im just being honest about the shit hell ive been stuck in greenville for 4yrs

    Leave a comment:


  • jwiles
    replied
    Originally posted by mr.vang
    its all money. is it really worth spending 10K on an eta to get 250hp when a s50 swap can be down under 5k.
    im leaning extremely hard in that direction. I NEED SOME SPEED IN MY LIFE!

    im 21 and have been stuck in a nissain pick up since 17.

    Leave a comment:


  • mkcman17
    replied
    Agreed, my car was THE tester car for the GE stuff, we went through a lot of spring rates and heights, and with 6" spring and camber plates we found I could still get reasonably low (see sig) and still have a very live-able ride. The 4" springs are unbearable.

    Leave a comment:


  • PNWDan
    replied
    Originally posted by jwiles
    Does anyone know of a brand that does not require welding, and has 30+ clicks for damping, basically something i can just drop in " in this imaginary world" 04/1986 325e i dont have a decent welder {I} can trust.


    side note why after 20+ yrs has no one come up with better opions for eta performace upgrages than swapping in an i head or pulling the engine completely. theirs power in masses. except for if you one and eta

    s>0
    e<100%
    Th:Tc
    For your first question I would say..

    German Engineering with Billy sports. No idea why you need 30 clicks of anything on an E30 shock. I can't even imagine you could begin to push that car so hard that you need it...

    That being said, GE coilovers are basically bolt on with the exception of cutting above the weld to remove the perch. The spring rates are a great match to Billy sport inserts...

    For your second question, simply put.. its an economy engine made for fuel mileage. The reason nobody has came up with better performance options is because there aren't any reasons to. With m20b25 swaps as well as other swaps being common, nobody wants to dump a ton of cash into a turd engine. That's why the "I" head swap is and always will be the best bang for the buck.

    Leave a comment:


  • mkcman17
    replied
    You're sure a cocky sonobitch. You happen to go to clemson?

    Stop being a lazy bum, buy a cutoff wheel, take off the perch and run adjusters and 5" springs. Done.

    Leave a comment:


  • mr.vang
    replied
    Originally posted by jwiles
    Does anyone know of a brand that does not require welding, and has 30+ clicks for damping, basically something i can just drop in " in this imaginary world" 04/1986 325e i dont have a decent welder {I} can trust.


    side note why after 20+ yrs has no one come up with better opions for eta performace upgrages than swapping in an i head or pulling the engine completely. theirs power in masses. except for if you one and eta

    s>0
    e<100%
    Th:Tc
    its all money. is it really worth spending 10K on an eta to get 250hp when a s50 swap can be down under 5k.

    Leave a comment:


  • jwiles
    replied
    Originally posted by mkcman17
    There's the matter of the spring perch in the way. And an 'i' head swap IS the best bang for the buck on an eta, the head is garbage.

    As stated, JOMS require no welding or modification because of the weird V-shaped design on the spring.

    JOMS? if thats the case then this buck doesnt have much bang. id rather hit a deer {knocks on wood}, but i might be able to get my hand on an I engine since my buddies dropping an ls1 in a vert for some reason and belives hes going to make 600+

    Leave a comment:


  • jwiles
    replied
    Originally posted by bmwguy325is
    Man i got cheated my shocks on have 22 clicks of adjustment. That must mean they are rubish.....
    As for not welding it going to be a bolt on affair.
    I think what you need to do is call the BMW engineer that made the spindle part of the shock tube.......
    If i keep at the rate im going i will be the damn BMW engineer.

    Mechanical Engineering / Automotive Engineering

    Leave a comment:


  • mkcman17
    replied
    There's the matter of the spring perch in the way. And an 'i' head swap IS the best bang for the buck on an eta, the head is garbage.

    As stated, JOMS require no welding or modification because of the weird V-shaped design on the spring.

    Leave a comment:


  • bmwguy325is
    replied
    Originally posted by jwiles
    Does anyone know of a brand that does not require welding, and has 30+ clicks for damping, basically something i can just drop in "
    Man i got cheated my shocks on have 22 clicks of adjustment. That must mean they are rubish.....
    As for not welding it going to be a bolt on affair.
    I think what you need to do is call the BMW engineer that made the spindle part of the shock tube.......

    Leave a comment:


  • IronFreak
    replied
    Ground Control..........

    Leave a comment:


  • CW325
    replied
    Jom and raceland coilovers dont require welding. Not sure if theres others.

    Leave a comment:


  • TYBG
    replied
    i feel your pain. that eta lifestyle bro

    Leave a comment:


  • jwiles
    started a topic Coilovers that dont have to be welded

    Coilovers that dont have to be welded

    Does anyone know of a brand that does not require welding, and has 30+ clicks for damping, basically something i can just drop in " in this imaginary world" 04/1986 325e i dont have a decent welder {I} can trust.


    side note why after 20+ yrs has no one come up with better opions for eta performace upgrages than swapping in an i head or pulling the engine completely. theirs power in masses. except for if you one and eta

    s>0
    e<100%
    Th:Tc
Working...