16X8 +7 tire fitment

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Aswilley1
    replied
    Originally posted by IRON-E
    This is 205/45/16 square 16x8 front 24 offset, 16x9 rear 14 offset with 15mm spacers all around.

    Looks perfect, kinda the look I am going for too. What Suspension are you running and how much drop? Also what fender mods did you have to do? Rolling only, or pulling too?

    I ask because my set up is very similar. I am looking at running a 16x8 ET25 all around, and also slapping 15mm spacers all around. I want to run a 205/45/16 because it sits exactly how I want.

    Just trying to see what all I will need to do to put them on nicely without rub. I am on a fully stock suspension right now, but eventually plan to dropping it with coilovers 1.25" front, and 1.5" rear.

    I am not to worried about the rear rubbing too much; I think there is plenty of room to have a 16x8 ET25 +15mm spacer with a 205/45/16 back there without fender work. The fronts however, I am worried will need some fender work to not rub and clear the struts considering the offset and spacer. .

    Leave a comment:


  • IRON-E
    replied
    This is 205/45/16 square 16x8 front 24 offset, 16x9 rear 14 offset with 15mm spacers all around.
    Attached Files

    Leave a comment:


  • masterofnone
    replied
    Thanks for the reply Bob!

    My fenders are rolled pretty tight and pulled ever so slightly as to not disturb the original line.

    At a point in time I was running Ferrari 348 wheels (17x7.5 ET-1 with 195/40s) up front. I was not able to turn my steering wheel more than one rotation on a stock rack without hitting fender. But I was also going for a form over function ride height back then. Rears were 17x9 ET3 on 205/40s. Not worried about fitting rears.

    According to online calculators, comparing the two setups, the corners of the tires should be in about the same location but the 225/45s at ET10 would be taller.

    Untitled by Evan Nessim, on Flickr
    Untitled by Evan Nessim, on Flickr

    Pics brought to you by Miss Courtney Cutchen.

    These were my style 5s with 5mm spacers front and 205/45s, no issues for sure. I plan on raising the car even more to allow clearance for Z3M diff cover vs. speed bumps.

    Untitled by Evan Nessim, on Flickr

    Leave a comment:


  • AWDBOB
    replied
    It depends on how much fender work you want to do. The front lip is small and hard to work with, so when you roll them flat it pushes the fender out pretty hard and makes it look odd in some cases. With the 215/45 on a 16x8 above on my car I don't rub up front (but it's close) at ET13. I am 100% sure 225/45s would have me rubbing (still no roll up front) and the loss of 3mm (et10 vs et13) with the wheels you want to run wouldn't be helping.

    Leave a comment:


  • masterofnone
    replied
    16x8 friends, I need your help!

    Im looking at getting 16x8 ET10s and want to run 225/45s. I feel this may be on the hairy edge of possible.

    What do you guys think?

    Leave a comment:


  • Pootis
    replied
    Agree to disagree I guess. I think that is way too much sidewall imo. Here is another pic of my setup.
    16x7.5 +15
    16x8 +13
    205/45/16 all the way around


    I'm on ground controls and pretty low. If you want to run it this low you will have to roll the fenders in the rear.

    Leave a comment:


  • sampayne
    replied
    Originally posted by AWDBOB
    Neither, fill and drill. Thanks man!
    Oh, awesome! I want style 5's and keep going between fill and drill or adapters.

    Leave a comment:


  • AWDBOB
    replied
    Originally posted by sampayne
    5 lug swap or adaptors? Looks great.
    Neither, fill and drill. Thanks man!

    Leave a comment:


  • sampayne
    replied
    Originally posted by AWDBOB

    5 lug swap or adapters? Looks great.
    Last edited by sampayne; 03-08-2018, 07:54 PM.

    Leave a comment:


  • AWDBOB
    replied
    Originally posted by hakstern
    Ok that sounds good! I like the stance of your car. What suspension are you running?

    So the final verdict will be 205/50/16 I assume.
    It's all Ground Control. Once I put the motor in and get it all back together I'll have to do a real ride height adjustment.

    Leave a comment:


  • MrBurgundy
    replied


    16x8 205/50/16 is the way to go


    Sent from my iPhone using Tapatalk

    Leave a comment:


  • hakstern
    replied
    Originally posted by AWDBOB
    16x8 +13 Front
    16x8 +8 Rear

    215/45/16

    IMO, I would run a 205/50 not a 205/45.

    Ok that sounds good! I like the stance of your car. What suspension are you running?

    So the final verdict will be 205/50/16 I assume.

    Leave a comment:


  • AWDBOB
    replied
    16x8 +13 Front
    16x8 +8 Rear

    215/45/16

    IMO, I would run a 205/50 not a 205/45.

    Leave a comment:


  • hakstern
    replied
    Originally posted by Pootis
    [IMG][/IMG]

    205 45 16 will be a good tire. I wouldn't go any smaller. Here is a pic of my car with a 16x8.5 +13 wheel and a 205 45 16 tire. The fronts will be just fine with that setup as well.
    Do you mind posting up more shots please.

    What suspension are you on?

    Leave a comment:


  • Pootis
    replied
    [IMG][/IMG]

    205 45 16 will be a good tire. I wouldn't go any smaller. Here is a pic of my car with a 16x8.5 +13 wheel and a 205 45 16 tire. The fronts will be just fine with that setup as well.

    Leave a comment:

Working...