BBS Garage: All things BBS

[R3Z3N]

Where can one purchase inverted lips for a BBS RS 17"? (IE .5" or 1")


Specifically this is what I have:
- BBS RS 262 17x8 (Fronts)
- BBS RS 263 17x9 (Rears)

[fporro]

presitigewheel.com has you covered



Frank, Im pretty sure you know this info, but in case you dont, 16" rs have a 12.25" face, and 17" rs have a 13" face.

Yeap, just measured a set of 16" BBS RS 34 holes centers, they come in a bit over 13", I'm still a little short then., thanks.

[thebutcher37]

Can anyone identify this waffle?
Its metal, but the nut is plastic.
EDIT NeverMind.. I found out its from a miata.

[formula driver]

Got a link or a way to contact them?

presitigewheel.com has you covered

Aloha,

Here's a few pics of RS's 003's and 15mm H&R spacer and 11mm (5+6mm) staked spacers to clear Wilwood's 6 pot front brakes.

What I really need is rim's that have centers with overall 13.375" diameter, measured at lip bolt's., washer and O ring represent lips



[/IMG]

Frank, Im pretty sure you know this info, but in case you dont, 16" rs have a 12.25" face, and 17" rs have a 13" face.

[Eric]

Completely stripped, 1 fiberglass seat, fiberglass front and rear bar, smaller fuel tank, no heater/fan box... basically anything that doesn't serve a purpose on the track isn't there...

I'm at 2630 with a full tank, all metal body panels (cf sunroof though) no heater box, etc. I do have a euro S50B30, which I think is a bit of a heavy motor, and a 4 door. I'm thinking that gutting the doors might get me 100lbs???

2300lbs is my goal, but I don't know where I can shave another 330lbs...

Are the brake pads fresh?

Pad depth doesn't change with 4 piston calipers like it does with sliding single piston ones.

[noE30]

Here's one of the wheels I just refinished, repainted the faces gold, polished lips/caps, and new chrome bolts.
Its a RS018 5x130 16x9 et36. Should be mounted on my e30 sometime next week I assume, just need to refinish one more wheel (3 are fully done) and order valve stems.
Rears are RS018 and fronts are RS131 16x8.5 et56.


IMG_0815res by m_colby, on Flickr

[noE30]

I just bought brand new stems directly from BBS in Georgia. Less than $25 for all 4.

J

Got a link or a way to contact them?

[slippery]

Wheres the best place to find metal valve stems that will fit my rs 131s? Im using the stock lips with the "reverse lip", seems like the bolt or washer are too wide to fit inside the lip.

I just bought brand new stems directly from BBS in Georgia. Less than $25 for all 4.

J

[fporro]

^ yeap, less than 16k's on them.

[IronmanE30]

Are the brake pads fresh?

[fporro]

Aloha,

Here's a few pics of RS's 003's and 15mm H&R spacer and 11mm (5+6mm) staked spacers to clear Wilwood's 6 pot front brakes.

What I really need is rim's that have centers with overall 13.375" diameter, measured at lip bolt's., washer and O ring represent lips



with 11mm spacers (5+6mm) ...

[noE30]

Wheres the best place to find metal valve stems that will fit my rs 131s? Im using the stock lips with the "reverse lip", seems like the bolt or washer are too wide to fit inside the lip.

[-negrito-]

Any fender mods? I doubt those will work with adapters.

Im planning to widen the fender.

[formula driver]

Question, I purchased a set of BBS RS 021 and I believe the front will poke out too much, I dont know much on proper offset.

Specs:
5x120
Front:16x8 et11
Rear: 16x9 et24

Just want to confirm are they doable? If they do poke, I am planning to widen the fenders either way.

Thanks in advance.

Edit: forgot to mention Im going to use adapters

Any fender mods? I doubt those will work with adapters.

Swap the lips and keep them in the same front and rear.

These have 2" lips, squared.

Where are you all getting your sealant from? Online? or can I just use black rtv sealant you can find at any auto parts store?

Yup, that stuff works great!

[noE30]

Where are you all getting your sealant from? Online? or can I just use black rtv sealant you can find at any auto parts store?