BBS Garage: All things BBS

[fporro]

I got a question. You selling?

$ 1,200 + s/h from 96821 link ... http://www.r3vlimited.com/board/showthread.php?t=240242

[formula driver]

Yeah, I'm thinking of 15x8 front and 15x9 rear just for shits & giggles.

Do you think the ET38 will have issues with clearing the shock / brakes without a spacer? I have the 5mm spacers already, so that'd bring the offset to ET33 (closer to bottlecap fitment).

Also, I'm unable to seperate the parts of the wheel because of whatever sealant BBS used, and my oven is too small to stick the wheel in to loosen it up. Any pointers?

If you cant get the wheels apart with a mallet...

Cut the seal with a razor, all the way around (should do this anyway), and use a heat gun around the entire seam. Do it for a few minutes, and the halves should split quite easily...

[hexagone]

If you cant get the wheels apart with a mallet...

Cut the seal with a razor, all the way around (should do this anyway), and use a heat gun around the entire seam. Do it for a few minutes, and the halves should split quite easily...

No heatgun required. A hammer and two blocks of wood are needed, and it takes a few seconds:

http://www.youtube.com/watch?v=44yMeoGsLcg

[Zasz]

Actually, the issue with mine was that the .5" lip was a pain to separate from the faces because I didn't have enough room to get the seal with a razor, I was just cutting the very edge of the sealant. I could tell the lip was able to budge with the mallet, but I didn't get enough leverage somehow.

All I ended up doing was prying the lips off with a large flathead screwdriver, worked like a charm.

Edit: Somehow, even a blowtorch didn't work.

[formula driver]

No heatgun required. A hammer and two blocks of wood are needed, and it takes a few seconds:

http://www.youtube.com/watch?v=44yMeoGsLcg

Do you know EVERYTHING bro?

I use a hammer before I use any heat, and sometimes it works (most of the time) if not, than I use a heatgun, and then they split apart, quite easily.

While your here hex, Ill voice a warning for others. Steer clear of this guy, folks, he burnt me BADDDD on a set of rs285's...

Price was not horrible, and he offered a refund, but the issue was that he was VERY dishonest about how he described them.

Let me know if you'd like to see the pics of these things...

I dont like you dude, Im trying to be an adult about this whole thing, but do me a favor, and dont quote my post's. It just reminds me of how pissed I am, and how bad you SUCK.

[e30lyf]

^^^ relax bro..

[hexagone]

Do you know EVERYTHING bro?

I use a hammer before I use any heat, and sometimes it works (most of the time) if not, than I use a heatgun, and then they split apart, quite easily.

While your here hex, Ill voice a warning for others. Steer clear of this guy, folks, he burnt me BADDDD on a set of rs285's...

Price was not horrible, and he offered a refund, but the issue was that he was VERY dishonest about how he described them.

Let me know if you'd like to see the pics of these things...

I dont like you dude, Im trying to be an adult about this whole thing, but do me a favor, and dont quote my post's. It just reminds me of how pissed I am, and how bad you SUCK.

This isn't adult behavior. You're acting childish and i'm going to quote you again because you look like a fool posting this drivel.

For anyone so absolutely curious what this nonsense is about, please refer to this thread below:

http://www.s14.net/forums/showthread.php?t=54675

[formula driver]

^^^ relax bro..

no...

This isn't adult behavior. You're acting childish and i'm going to quote you again because you look like a fool posting this drivel.

For anyone so absolutely curious what this nonsense is about, please refer to this thread below:

http://www.s14.net/forums/showthread.php?t=54675

Your right, and I agree, but its VERY hard to act like an adult, when I have punk kids like you screwing me over on wheel purchases, and than prancing around the net, quoting my post's like nothing happened.

And you keep doing everything you can to make me look bad, thats your defense.

I dont like you Asim, I feel that you burned me pretty bad, now do me a favor and dont quote my gd posts, stay out of my hair, and Ill stay out of yours.

[mbonanni]

Anyone know anything about BBS rs 601?
34 bolts
4x100
16x7.5 I think.

Can't find much info on them.

[formula driver]

really really proud of these!

But man Im sore...

BBS RF 011/004

17x9 et7 17x10 et15

Prima Donna theme

80% gloss white powdered faces/waffles
24k gold painted hex caps
24k gold plated bolts
Gloss black powdered inner barrels
Semi gloss powdered nuts
Red/Gold JDM BBS caps
Mirror polished Newish 2.5"/3" stepped lips

[Pl3wA]

^EWWWWW!!! how much?

[Court M3]

Found a couple sets of 1/4 caps guy wants around $11- for each set, but need refinishing. Not a big deal as they would have to be done to match wheels anyway. How rare are these and does that sound like a fair price?

Pics of what he sent

[fporro]

They always come handy, specially if you're into RS's.
$ 11 very fair.

I need a set of 4 for my RS033's.

[kreasims]

It's more like 1/2 height caps of BBS RG and I dont think those fit RS. Ask for a photo of the back of it to confirm.

[kreasims]

Want to buy BBS E52 center, preferably PCD 5x130 but will take any PCD's. Hit my inbox if you wanna let go. Thanks :)

Pic: