Toughest job in an e30?

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • 92 mtechnic cabrio
    replied
    Originally posted by einstein57
    i was like 6 months old when that movie came out.
    So was I but you don't have to be so ig'nant 'bout it :p

    Leave a comment:


  • Firestorm
    replied
    Well where do i start....

    Leave a comment:


  • Maluco
    replied
    my toughest job in an E30 was actually a blowjob... I drove downtown to pick up this one chick that worked for TXU as usually did during lunch. We opted for just parking under one of the many exchange bridges that afternoon. Well, basically, she had braces and somehow we got hooked up. I can't even type right now cause I am still traumatized by this. She was laughing, I was freaking out, there was blood, I finally reached in there as best I could, "un-hooked myself", got over it and talked her into finishing while requesting she only continue on the head itself. There was no fkn way I was going to allow myself to go through that and not finish busting my nut. I have a few friends that never allow me to forget about this so....

    BTW, it was in an 84 318i so I guess I had it coming to me (no pun intended). I've since then allowed another bitch to wreck that car and pay for one of my new late model E30's ;). Blowjobs forever!

    Leave a comment:


  • kamotors
    replied
    rear wheel bearings for me.....i didn't have the right tools i froze the bearings so they fit in easier

    Leave a comment:


  • e30 gangsta
    replied
    Originally posted by moatilliatta
    it took me and a friend to do a dash swap in like 8 hours including breaks and food. first one weve ever did. had a bunch of extra bolts... oops
    the key is to take out the hvac panel. if not youll be there forever.

    Leave a comment:


  • matt
    replied
    Man... auto to manual swaps are CAKE after about 3.

    Leave a comment:


  • xLibelle
    replied
    my first job was auto to manual swap. yes, those top bolts were fun. But ive come across much worse dealing with a few rusted up shit boxes. sub frame removal for one.


    Originally posted by rs4pro3
    toughest job is replacing the windshield wiper motor without removing the fan and heater core.
    ely, didnt i enquire with you about this a few weeks ago?
    ended up having to remove the blower, dismount the wiper assembly, THEN remove the wiper motor, and lastly the assembly would come out.... what a pain in the back!

    Leave a comment:


  • moatilliatta
    replied
    Originally posted by e30 gangsta
    We did a dash swap in less than 2 hours 2 day. Its not that bad. Id say

    Reinstalling a full carpet with putting the carpet under the heater core. Also
    fixing a snapped rocker while keeping the head on the car.
    it took me and a friend to do a dash swap in like 8 hours including breaks and food. first one weve ever did. had a bunch of extra bolts... oops

    Leave a comment:


  • NC325iC
    replied
    torch has been done, ask jordan about it used to have a video

    rear subframe - pita but i wouldnt say hard, cutting through the bushings with a hacksaw blade untill you could bend them in with a screw driver was an ass pain but whatever

    clutch/tranny swap - worst part may have been getting the output flange on, that or having the starter stick down in the way of putting the tranny back on until you realize the next day, worst part actually was having the flywheel resurfaced and not balanced afterword then installing it all back and not being able to rev past 1k for fear of shaking car to peices then taking it all back out again (i had the tranny in and out atleast 3 times) i think if i were to do it right now i could have it out in about half an hour not counting jack time

    engine swap - took a while but the only instruction i had was from bentley, wasnt too hard i dont think

    shocks and struts- had one of the oe gland nuts stick had to take it to a shop to get it off, fucked up a tie rod ball joint, not badly enough to replace it at the time :rollseyes:, only to have it come out on my way to school a few days later (16 years old)

    convertible top replacement - tedious

    taking of the intake mani can be a bit of a pain

    like someone else said, none of the jobs are really hard, just time consuming the first time (i havent had to replace heater core, wiper motor, but i think over christmas im finally gonna install the r134a components, ill get back to you on that)

    Leave a comment:


  • SamE30e
    replied
    First job I did on my E30 was the clutch..

    That top bolt is the biggest pain in the ass, I can't see anything else really being more difficult than a clutch.

    Leave a comment:


  • TS87325IS
    replied
    rear wheel bearing was not too fun , until I made a puller for it , and the damn screws that hold the obc in suck if you keep dropping them.

    Leave a comment:


  • oldskool3
    replied
    i heard sawzall as well but I figured torch would be a lot easier than fucking with a sawzall.

    Leave a comment:


  • M5wanaB
    replied
    Originally posted by oldskool3
    I heard it was possible to torch the old subframe bushings until they melt out. has anyone ever tried this?
    Ive heard sawzall them out. But I dont remember if that was for E30 or E34, Ive had both.

    Leave a comment:


  • oldskool3
    replied
    I heard it was possible to torch the old subframe bushings until they melt out. has anyone ever tried this?

    Leave a comment:


  • atomic
    replied
    Originally posted by LivingLegend06
    Are you kidding me? I did mine in the parking lot at the auto store in like 3 minutes.


    And 2 and a half minutes of that is opening the damn packaging they are in too .....

    Leave a comment:

Working...