Anybody want to take any bets?

[Wh33lhop]

So it's modded now. 3.15LSD, Konis and UUC sways. 4 and a half months.

[Wh33lhop]

I needed some FAGs in my rear end, wheel bearing time!

Old one out.


New bearing in


Hub


Hub in


Freakin' ebrake back in. Pain in the ass.


Brake on


Finally down on the ground

[Wh33lhop]

Metric Mechanic built 3.15LSD with 3 clutches and 30 degree ramps.


Old seals out


New seal


New seal in. Did not replace the spring clips which turned out to be a mistake. This side does not hold the axle stub in. Still need to tear it apart again and replace that stupid clip.


Exhaust and heat shield out


E sockets for the input and output shaft bolts


Separating the driveshaft was weird. Didn't budge prying against the crossmember/brace, had to remove crossmember and pry against the input flange.


2.93 ready to come out


Diff out


2.93 out and 3.15 on the ground


Rear UUC sway vs. stock


Diff and rear sway in, this was a pain in the pitch dark with no light


Front sway in (next day)

[Wh33lhop]

Oil change (leveling the car out)


Glad I had this 36 from before


Old water pump out... I think this was original, although the rest of the cooling system is new.


Stewart pump and URO metal pulley. Yeah it's overkill but I don't want to worry about it.


God damn it BMW.


Luckily I had spares


No pic of after. Replaced pulleys, belts and bled coolant.

[Wh33lhop]

Been busy with this car.

Fuel filter.


Doneski.


Little cameo with E30 which will be running again soonish.


Herro herro, what do we have here?


Up we go


Stock 90k mile struts


Awesome shop spring compressor


All buttoned up


WTF BMW... why do you make me tear your insulation?


Old and new


Konis on and ready to go, car is completely transformed.

[N2MYE30]

Awesome post wh33lhop. I got a good lesson on what all the hubbub is about.

[justint5387]

Gay car

[EürOV3R]

zhp cams are only $300. hopefully they'll be in the next round of pics.

[davem]

jelly about those floor mats, e36 ones are NLA :(

[Bimmerman325i]

Funny you didn't mention the baller headlight covers.

[Wh33lhop]

All weather floor mats and ZHP knob



Here's the old K&N filter versus a plain jane paper filter. Which has more filter media... hmm.



Ready for surgery



Vanity cover off



Not gonna lie, this is not a sight I'm used to. This is the first car I've bought that had zero leaks.



Leveling it out to drain the oil. Not enough room for a jackstand so a wheel is a better safety precaution than nothing.



I happened to already have a 36 from doing E30 wheel bearings



Reverse thread!



Got it off



Helical splines



Intake piston out



Bearings



Outer washer--this is what the rattle kit replaces



Everything (do NOT use normal size vice grips if you do this, even with lots of padding they marred up the surface of the piston and I had to shave it down with a dremel. If I did it right the seal should not be compromised but if I missed a spot it will score the bore of the vanos and I'll basically need a new unit after awhile. Use a vice or possibly larger vice grips, the "medium sized" grips are too small to grip the piston properly)



Unfortunately we ran out of time and need a few more parts, so we called it a night at about 9PM. Not the most flattering pic, lol

[Rsully70sev]

:up:

My favorite shift knob.

[Wh33lhop]

There I modded it.

[chadthestampede]

blacked out grille=not stock

[Brezzi]

dat drop top e-class tho