Blunttech e12 LSx / t56 swap

[jakeb]

Car is back to Blunt now...

A couple finished pictures to post.

[garretvs]

I have been fixing a couple small things the past couple weeks. Small exhaust leaks, oxygen sensor not giving a reading (bad connector not allowing the heater to work), etc

Here is the bad O2 sensor connector. It was pushing the mating connector out and not allowing them to plug together.


Because of the lack of room I wasn't able to use a flange to keep the pipes together so I had to use band clamps. They were not sealing...mostly because I wasn't cranking them down enough. 70-80ft lbs and now they are sealing.

Leaks are sealed up...got it aligned today. And now on to doing some adjustments to the tune. The PCM is from a 2002 camaro but then I blind adjusted it somewhat and it needs more fueling from what I have logged so far. The PCM will pull it back with the O2 sensors to stoich but it is much better to have the tune very close and not need the PCM to adjust so much.

A couple pictures of the just about finished engine bay. Still need to swap the AC drier, fill the AC, and put the strut tower brace back on.

Nice clean swap! Good to see the A/C works; This one should surprise a lot of posers driving around out there 8-)

[ZM Blue Devil]

Epic! Videos please.

[F34R]

Blunttech cock n balls, I am done that is too funny.

Amazing job Jake, cannot wait for some videos!

[blunttech]

Fucking awesome! Love the keychain, lol.

lol I know That just made my day

[MR 325]

Fucking awesome! Love the keychain, lol.

[blunttech]

Made it home at 230am
raced a late model STI in wisconsin after badgering him for miles .. He wanted nothing to do with me after looking at the car as he didnt want to waste his time Im sure.. but I kept after him.. We finally went from a 30 roll and I smoked him. Got pulled over for speeding and loud exhaust at 100am.. Nice cop... Let me off .. Shined his flashlight on the cock n balls on the console... Held the light on it for a while and then said "Have a nice night" . lol He didnt say anything about it
Car is a beast and Jake did an amazing job. It feels very balanced and handles great with all the new suspension and big sways. Id highly recommend Jake if youre looking for a swap of any sort,...

[jakeb]

sorry no video....

[LJ851]

Nice work Jake.

Smokey burnout vid?

[jakeb]

Steve just left with the e12.

A couple of surprises for him.

[Good & Tight]

Looks really nice Jake Im booking a flight as soon as you ok Friday at 3pm arrival is ok

Nice work, somebody is going to have fun with it..!!!!!

[blunttech]

Looks really nice Jake Im booking a flight as soon as you ok Friday at 3pm arrival is ok

[jakeb]

I have been fixing a couple small things the past couple weeks. Small exhaust leaks, oxygen sensor not giving a reading (bad connector not allowing the heater to work), etc

Here is the bad O2 sensor connector. It was pushing the mating connector out and not allowing them to plug together.


Because of the lack of room I wasn't able to use a flange to keep the pipes together so I had to use band clamps. They were not sealing...mostly because I wasn't cranking them down enough. 70-80ft lbs and now they are sealing.

Leaks are sealed up...got it aligned today. And now on to doing some adjustments to the tune. The PCM is from a 2002 camaro but then I blind adjusted it somewhat and it needs more fueling from what I have logged so far. The PCM will pull it back with the O2 sensors to stoich but it is much better to have the tune very close and not need the PCM to adjust so much.

A couple pictures of the just about finished engine bay. Still need to swap the AC drier, fill the AC, and put the strut tower brace back on.

[TrentW]

Thumbs up indeed.

[golde30]

Can't wait to see some tire carnage.