Announcement

Collapse
No announcement yet.

Svetlana gets M power. My 91 318is s52 swap (Engine Out) )

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Svetlana gets M power. My 91 318is s52 swap (Engine Out) )

    Svetlana my bae

    Giving her M power.
    Last edited by Mistawall; 06-10-2014, 08:27 AM.
    my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

    #2
    OK SO FAR I HAVE OBTAINED
    98 M3 s52 with 158,xxx w/ wiring harness and comps
    zf transmission
    3.23 lsd with no flanges
    mz3 diff cover
    e34 oil pan stuff
    Flywheel clutch
    Condor mounts
    Send DME to have EWS removed

    AND I NEED

    driveshaft (would any m3 drive shaft work?)
    16" spal fan
    Rewire harness for e30.
    make engine bay nice nice.
    MORE MONEY
    other stuff

    5-13-14 M42 Is OUT

    This is svetlana waiting for m power


    this was before i put the other m42 in it and still had my hub caps.. >:(
    Last edited by Mistawall; 12-15-2014, 10:15 AM.
    my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

    Comment


      #3
      1/7/14 Engine Got Delivered Today!!! came with the exhaust and wiring harness
      Last edited by Mistawall; 01-07-2014, 07:36 PM.
      my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

      Comment


        #4
        Sub'd! Planning on converting to OBD1?

        Comment


          #5
          Sub'd also. I am doing the same swap into my vert. S52. Still collecting parts also.

          Jay

          Comment


            #6
            Originally posted by TheNorthBest View Post
            Sub'd! Planning on converting to OBD1?
            Na im gonna keep it ODBII gonna try to remove EWS myself
            my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

            Comment


              #7
              got my oil pan and motor mounts

              my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

              Comment


                #8
                Svetlana gets M power. My 91 318is s52 swap (NO PROGRESS YET)

                My pile of parts

                Took my wiring harness off to remove the auto transmission wires


                Was left with these 4 abs related wires


                Cut off my x20


                Labeled the wires with the corresponding pins and crimped new connectors on them so i can put them in the c101 connector i bought from bmw with the pins


                Apparently these wires dont have much use


                Sent from my iPhone using Tapatalk
                Last edited by Mistawall; 02-20-2014, 07:39 PM.
                my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

                Comment


                  #9
                  Some photos of the engine


                  Lil dirty


                  Is there supposed to be a sensor here on the s52?



                  Sent from my iPhone using Tapatalk
                  my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

                  Comment


                    #10
                    Got my oil nut and e60 shifter woot
                    my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

                    Comment


                      #11
                      Nice!

                      Comment


                        #12
                        My pile is growing
                        my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

                        Comment


                          #13
                          Been slowly preping the engine takin bits and pieces off cleaning the block and whatever else i can. Turns out the right engine mount arm was cracked so i gotta get a new one of those.




                          You think the water pump is still good?
                          my build thread http://www.r3vlimited.com/board/showthread.php?t=309778

                          Comment


                            #14
                            Get rid of that water pump, put a CAST metal impeller in there

                            Check Us out on Facebook
                            Needing a harness adapter or wiring help? Check it out: also have 24v motor mounts, E30 M3 covers and E36 ECU mounts!
                            Full Product Line Tuning
                            OBD2 Tuning Available! OBD2 E36, S54 Swap, S62 Swap, etc: tuning@MarkertMotorWorks.com Dyno Thread

                            Comment


                              #15
                              Originally posted by 328ijunkie View Post
                              Get rid of that water pump, put a CAST metal impeller in there

                              ^That's what Dave is doin for mine!

                              Comment

                              Working...
                              X