M42 turbo dyno results

[gearheadE30]

Interesting about the torque hump from 3k to 3500 revs-I have the same, but more like 3k to 4500. Time to get mine dyno'd as well, although 0.5bar on stock internals won't be anywhere close haha. Always good to see turbo M42s.

fwiw have you ever run a small case diff on the car? I'm kinda assuming not, but I'm trying to figure out if I should put a medium case in/if the small case will hold up long.

[Schnitzer318is]

^Thanks Rob... appreciate it.

Unfortunately it looks like I have bigger fish to fry. Looked at my log today after a drive and it looks like either my turbo is running out of juice after 4500 rpm or my Hallman boost controller isn't up to the task of working with the internal wastegate on the turbo. I hit peak boost around 3500 rpm and then after 4500 it starts to bleed down to about 155ish KPA until redline.

I'll have to look into it... need to get this thing figured out before dyno'ing since the weather is now under 100 degrees here.

[rob_e30]

Very nice build. Color me impressed. Out of curiosity how much would you charge for that intake? I have that huge bump in HP and TQ between 3000-3500 with my turbo setup @12psi. Can we have more info on the water injection setup as well? I'm probably pushing the stock pistons as it as with my stock CR, but maybe in the future I'll upgrade. You know, after this head gasket gives up the ghost.

Now I can't wait to get my car dyno'd. Thanks for the info. Love to see turbo M42's.

We're running an Aquamist water injection system that we purchased from Howerton Engineering. He specializes in upgrades for Mini-Coopers and was very knowledgable and helpful.

[rob_e30]

did you have to do any retro fitting to make the make m42 mate up to the g260 you guys were running for awhile? what fly wheel are you currently using

It was not a match made in heaven as the transmission is a different length requring a different prop shaft length or moving the engine forward.

We're running a lightened M20 flywheel.

[call me jack]

did you have to do any retro fitting to make the make m42 mate up to the g260 you guys were running for awhile? what fly wheel are you currently using

[e30pq]

When are you going to be running in Phx next.. want to check this car out! :)

They usually have a club race in March and October every year.

We made the March race this year and the October race was moved to Vegas and then cancelled.

So if all goes well we should be back there early next season.

[j0oftheworld]

When are you going to be running in Phx next.. want to check this car out! :)

[e30pq]

We've had the G240 in the car since last September (09).

So far so good. We drive the car hard and the trans is holding up. We keep a spare G240 in the trailer just in case.

[yyi]

sick sick numbers...... very jealous

[tomgt325]

Are you using the getrag 240 still? If so, how's it holding up to the power?

[e30pq]

Yes, the compression ration is 8.5 to 1.

[Schnitzer318is]

Very nice build. Color me impressed. Out of curiosity how much would you charge for that intake? I have that huge bump in HP and TQ between 3000-3500 with my turbo setup @12psi. Can we have more info on the water injection setup as well? I'm probably pushing the stock pistons as it as with my stock CR, but maybe in the future I'll upgrade. You know, after this head gasket gives up the ghost.

Now I can't wait to get my car dyno'd. Thanks for the info. Love to see turbo M42's.

[Dj Buttchug]

What's your CR with the JE's?

im assuming the ratio is 8.5:1

[call me jack]

We can build you a custom intake if you're serious about one.

when the time comes that i'm ready to install it, i'll probably take you up on that offer. Still trying to locate an m42 e30 that i really like. :p

going to look at one next week.

[Ryann]

What's your CR with the JE's?