Official NorCal For Sale Thread

[Rev Run D]

30 bucks for a clean check panel from a 89.

[mazzo]

I have a set of OZ competition wheels + tires for sell:
17 x 7.5 ( ET38 )
4 x 100 lug
Newly refinished surface
205/45/17 Falken tire with 70% thread left
Comes with center cap and wheel nuts (stud not inlcuded)
$500 Firm Local pickup.
Thanks!

Matthew

[Rev Run D]

50 bucks for a decent is rear spoiler. cut the studs off, and applied 3m tape on it already. It's ready for sanding and a paint job!

[jayuuey]

wtb m20b25 ICV - T or L shape

fs Vibrant 1148 dual tip muffler $100, also have a 12" resonator.

[catech11]

from a doc I have, all my shit i gotta get rid of:

e30
taillights, early
shadowline window lockstrips
zender front valence
mtech I delphin sideskirts
mtech I delphin rear valence
early parcel shelf
driver sport seat (some damage to bolsters)
m20b23 block
m20b23 head (200 casting ‘78)
8x TRM C1 15x7, mediocre star specs


let me know if anything strikes your fancy, folks

PM'd you about TRM's

[36brua]

prices ?? any pics and cost of zender valence early diving board or later ?thanks

from a doc I have, all my shit i gotta get rid of:

e30
taillights, early
shadowline window lockstrips
zender front valence
mtech I delphin sideskirts
mtech I delphin rear valence
early parcel shelf
driver sport seat (some damage to bolsters)
m20b23 block
m20b23 head (200 casting ‘78)
8x TRM C1 15x7, mediocre star specs

e36
driver sport seat (light damage to lower bolster, seat back recline inop)
m3 ‘97 steering rack (leaks)
a billion used motor mounts

e24
l-jet bananafold, tb, boots
l-jet ECU, AFM, front timing sensor, engine harness (M90)
tailights
euro front bumper trim
rear interior rub strips and chrome trim

e12
bilstein sport dampers F/R

e28
c-pillar sails
m30b34 intake manifold, TB
dirty ECU, harness, injectors
dual mass flywheel + clutch

misc
e21 320is wheel (coarse spline)
m10 turbo setup, almost complete
metric mechanic rally head
m10 dual valve springs
M106 turbo stuff (ecu, harness, manifold, turbo, piping, IC, AFM, WG)
Tial WG


let me know if anything strikes your fancy, folks

[kronus]

prices ?? any pics and cost of zender valence early diving board or later ?thanks

sorry, no prices until people express interest. I don't have time to research market on that whole giant-ass list..

the zender valence bolts up to early (pre-86) euro and US valences and is meant for euro bumpers

here's a pic:

[ohthejosh]

Id buy that zender valance but then Id look like Scott's lol.

[_Keith_]

M20b27 pulled and parting out. Have wiring and all.

Let me know if you want anything. Came from a 87

[mr2peak]

WTB/ Looking for late model Rear Bumper Mounts. Both the part that attaches to the car, and the part attached to the bumper. Had to cut my bumper off, frozen bolts :/

[kronus]

Id buy that zender valance but then Id look like Scott's lol.

nothing wrong with that

[ohthejosh]

nothing wrong with that

Nothing but I would like to have something different. Still have the pfeba lip anyway, so thatll do until i can find a 86 euro valance and run the jimmy hill

[j0000stin]

Selling my project. http://sfbay.craigslist.org/sby/cto/4800164310.html

[Navarone]

Mine is still on CL. I keep getting offers around $2300 but 5 people have just stopped responding after a few solid emails and "ok, thursday sounds good, what time?"

http://sfbay.craigslist.org/eby/cto/4764616378.html

[Rev Run D]

Tell me about it. When I was selling my car, only 1 bite, sold it to him. After I sold it, all these people who had previously contacted me about it started emailing me to see it.