I can clean your fuel injectors. Just pay for shipping and the fluid

[MEPEH]

I just checked out the site. Do you have any idea when you will have more 4 pintle m42 injectors? ;D

Is this what you are looking for ?

http://mepeh.com/index.php/refurbished-bmw-19lb-bosch-fuel-injectors-0280155700.html

Part Number 0280155700 Mustang Yellow injectors ?

I may be able to get it but It will take about 10 days to get you this order.

I will PM you a discount code for these injectors so you could get them for 10$ a piece, plus shipping (6$ to US/25$ international)

Let me know if you're still interested and i'll start ordering stock.

[MEPEH]

Coupon code doesn't seem to be working for me?

PM'ed

Please only use the coupon if you check out as a guest.
No need to waste your time registering an account (unless you plan on shopping with me a lot :)

[jwal]

Is this what you are looking for ?

http://mepeh.com/index.php/refurbished-bmw-19lb-bosch-fuel-injectors-0280155700.html

Part Number 0280155700 Mustang Yellow injectors ?

I may be able to get it but It will take about 10 days to get you this order.

I will PM you a discount code for these injectors so you could get them for 10$ a piece, plus shipping (6$ to US/25$ international)

Let me know if you're still interested and i'll start ordering stock.

I think those are right...I have seen a ton of part numbers for these injectors.

My injectors are Part Number 0280150714 which are listed as 200 cc/min and 15.9 ohms of resistance here: http://www.injectorcleaning.co.uk/flow.htm

The part number you provided have the same flowrate, but a resistance of 14.5. Would this cause an issue?

[MEPEH]

I think those are right...I have seen a ton of part numbers for these injectors.

My injectors are Part Number 0280150714 which are listed as 200 cc/min and 15.9 ohms of resistance here: http://www.injectorcleaning.co.uk/flow.htm

The part number you provided have the same flowrate, but a resistance of 14.5. Would this cause an issue?

They will work as replacement for your 714 injectors.
The resistance will not matter, it's plug and play (drive)

[mpowerful]

280155700 and 280155710 are exactly same gen 3 bosch. Great 19lb 4 hole injectors!

[jwal]

Here are some part numbers, cc/min@3 bar flowrates and ohm resistance values that should be compatible with the m42. Its a long list :P

0280150413 205 15.9
0280150421 200 15.9
0280150428 205 15.9
0280150429 205 15.9
0280150454 199 15.9
0280150456 199 15.9
0280150463 199 15.9
0280150500 200 15.9
0280150501 200 15.9
0280150503 200 15.9
0280150505 200 15.9
0280150509 199 15.9
0280150560 200 15.9
0280150702 200 15.9
0280150704 200 15.9
0280150707 200 15.9
0280150711 200 15.9
0280150714 200 15.9
0280150721 200 15.9
0280150722 200 15.9
0280150725 200 15.9
0280150729 200 15.9
0280150730 201 15.9
0280150731 201 15.9
0280150734 200 15.9
0280150736 199 15.9
0280150741 200 15.9
0280150743 200 15.9
0280150747 200 15.9
0280150751 200 15.9
0280150757 200 15.9
0280150760 200 15.9
0280150762 200 15.9
0280150764 200 15.9
0280150766 200 15.9
0280150769 200 15.9
0280150776 200 15.9
0280150779 200 15.9
0280150783 200 15.9
0280150790 199 15.9
0280150902 205 15.9
0280150903 205 15.9
0280150931 200 15.9
0280150953 196 15.9
0280150954 196 15.9
0280150962 200 15.9
0280150976 200 15.9
0280150977 205 15.9
0280150978 205 15.9
0280150979 215 15.9
0280150980 215 15.9
0280150983 200 15.9

[mpowerful]

The body sizes and clip types do differ so id imagine that out of that list only a few might actually work. All of those are single pintle gen1s as well which basically suck.

[jwal]

Hmmmm ok, I believe you haha. I just cross referenced them from the list here: http://www.injectorcleaning.co.uk/flow.htm

I guess its outdated. If you dont mind me asking, why does the resistance not need to match the original injectors?

[xcx4x]

how many do i need?
how much for a new set?

[mpowerful]

Because the resistance refers to the resistance of the motor at 12v. The drivers that run the injectors are blind to that resistance so long as its within the range at which the driver can supply the current. That system uses high resistance which requires very low current. The system can tolerate say .5amps to 1 amp reliably which means it can basically use any high impedence injector 12-16ohms.

[dewme5]

Another satisfied customer. Ordered from mpowerful last week, and they were shipped immediately, and the results are a much smoother idling m20, with more power. Well worth the money I paid.

[MEPEH]

Another satisfied customer. Ordered from mpowerful last week, and they were shipped immediately, and the results are a much smoother idling m20, with more power. Well worth the money I paid.

Thanks :)

I finally got the famous Ford Yellow injectors
0280150700 and 0280155710

M42 Engine upgrade option :)

I have 4 sets available ATM and can sell them @ 40$ for a set of 4 Shipped to US, rebuilt with 1 year warranty... or an extra 25$ to ship Worldwide

[jwal]

Thanks :)

I finally got the famous Ford Yellow injectors
0280150700 and 0280155710

I have 4 sets available ATM and can sell them @ 60$ for a set of 6 Shipped to US, rebuilt with 1 year warranty... or an extra 25$ to ship Worldwide

Are these also compatible with the m42? If so I'll buy some now!

[MEPEH]

Are these also compatible with the m42? If so I'll buy some now!

Yes, you can read more info here

http://forums.bimmerforums.com/forum...ors-Are-Awsome!

[AndrewBird]

Just placed an order to have some injectors cleaned. Thank you SO MUCH for offering this service. You won't find a better deal anywhere.