guys using ZF trannys .........

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • e30rapidic
    replied
    I have a ZF trans with e30 master cylinder, E36 328 slave and dig it. Pedal is firm but engages close to about 1/3 of the way off the floor. Would love for engagement point to be a bit higher but it enables me to use a bit more ankle leverage than knee since the clutch is very sticky. Helps it not besing so jerky in stop and go traffic.

    also running Clutchmasters stage 1 e30 clutch setup and e30 325i TO bearing

    Leave a comment:


  • Mr.SWISS
    replied
    Originally posted by butters
    interesting, are porsches known for that? dad had an '88 911 several years ago, unfortunately I never got enough seat time to remember the clutch. but, isn't a low-catching clutch just a symptom of a poor bleed? it's the same basic ssytem as brakes, and perfectly bled best scenario is minimum pedal travel as there is no air to be squished through the lines before actually applying pressure. correct me if I'm wrong here.
    No your theory is all good, IDK why they were like that I thought it was a Porsche thing. I had a 90 C4, 86 951 and ended up in an 86 944 before I finally had enough punishment. You fall in love with the way that cr sounds when you crank, the safe like clunk of the dors shutting and that unmistakable Porsche smell. The upkeep is what killz it. :( S52E30 is damn close to the 911 accel tho for a 6th the cost!!! :up:

    Leave a comment:


  • butters
    replied
    Originally posted by Mr.SWISS
    I got used to the Pcar and like the clutch to grab just after letting off/up about 1/4-1/2 travel. Going with the OG E30 slave just need to get a new line this one bent...and the bend back snapped of course so I had to order a freshy.
    interesting, are porsches known for that? dad had an '88 911 several years ago, unfortunately I never got enough seat time to remember the clutch. but, isn't a low-catching clutch just a symptom of a poor bleed? it's the same basic ssytem as brakes, and perfectly bled best scenario is minimum pedal travel as there is no air to be squished through the lines before actually applying pressure. correct me if I'm wrong here.

    Leave a comment:


  • Mr.SWISS
    replied
    Originally posted by butters
    just to throw in my 2 cents here, I'm using a ZF unit with E30 master cylinder, E36 M3 slave and the feel is great. very firm pedal, engages right at the top. I was able to get a really good bleed with a pressure bleeder. clutch is not OEM, though, stage 1 DXD/south bend feramic.
    I got used to the Pcar and like the clutch to grab just after letting off/up about 1/4-1/2 travel. Going with the OG E30 slave just need to get a new line this one bent...and the bend back snapped of course so I had to order a freshy.

    Leave a comment:


  • butters
    replied
    Originally posted by nrubenstein
    My E30 clutch master with E36 M3 slave setup is not one that I'm happy with.
    Originally posted by atldohc
    are you referring to the fact that the clutch engages with the pedal coming right off the floor? this was my experience with those parts. i switched to a e36 325i slave cylinder and this corrected the problem for me. it engages about halfway up now, but the pedal has become noticeably stiffer
    just to throw in my 2 cents here, I'm using a ZF unit with E30 master cylinder, E36 M3 slave and the feel is great. very firm pedal, engages right at the top. I was able to get a really good bleed with a pressure bleeder. clutch is not OEM, though, stage 1 DXD/south bend feramic.

    Leave a comment:


  • Mr.SWISS
    replied
    So it seems the consensus is to install it all bled and and line attached I'm getting... Still looks tighter than a chinese virgin. Ordered a UUC line last night so I may put this off today.

    Leave a comment:


  • Wh33lhop
    replied
    Yep, lots of extensions and a wobble joint have done the trick for me many a time. You can compress the slave slowly if you just apply pressure to it.

    Leave a comment:


  • MattM
    replied
    Originally posted by Mr.SWISS
    so is it just me or is there no room to even install this thing (slave)without tilting it(ZF) down?
    its possible, an extension with a universal joint makes it easier... 2 extensions with the universal in the middle makes it really easy.

    shove it on, and get the bottom nut started by hand to hold it, then continue with the top one.

    Leave a comment:


  • Mr.SWISS
    replied
    so is it just me or is there no room to even install this thing (slave)without tilting it(ZF) down?

    Leave a comment:


  • nrubenstein
    replied
    Originally posted by atldohc
    are you referring to the fact that the clutch engages with the pedal coming right off the floor? this was my experience with those parts. i switched to a e36 325i slave cylinder and this corrected the problem for me. it engages about halfway up now, but the pedal has become noticeably stiffer
    Yes. I'm debating between the E36 M3 master and a 325i slave.

    Leave a comment:


  • Doughnut
    replied
    Originally posted by Ara
    ya no its cool, I just wanted to have everyone go and double check the position of the master cylinder's top section and have the ring to the right of the bracket ( above the pedal ).
    Okay, either I'm extremely ignorant or he still isn't explaining what he's talking about properly.

    I don't understand what he means by:

    "the position of the master cylinder's top section and have the ring to the right of the bracket ( above the pedal )"

    :-? Maybe a quick picture/photo to elaborate for the more "simple" crowd like myself?

    Leave a comment:


  • atldohc
    replied
    Originally posted by nrubenstein
    Of course, the E36 M3 clutch master and slave are a different diameter from the others, so it is relevant to a certain degree. My E30 clutch master with E36 M3 slave setup is not one that I'm happy with.
    are you referring to the fact that the clutch engages with the pedal coming right off the floor? this was my experience with those parts. i switched to a e36 325i slave cylinder and this corrected the problem for me. it engages about halfway up now, but the pedal has become noticeably stiffer

    Leave a comment:


  • nrubenstein
    replied
    Originally posted by M-technik-3
    This is the slave portion.
    Of course, the E36 M3 clutch master and slave are a different diameter from the others, so it is relevant to a certain degree. My E30 clutch master with E36 M3 slave setup is not one that I'm happy with.

    Leave a comment:


  • M-technik-3
    replied
    Originally posted by Ara
    haha you guys are hardcore lol

    well I just thought since its a master from a 97 M3 trans Id mention the trans it belongs to.
    This is the slave portion.

    Leave a comment:


  • Ara
    replied
    ya no its cool, I just wanted to have everyone go and double check the position of the master cylinder's top section and have the ring to the right of the bracket ( above the pedal ).

    Leave a comment:

Working...