Swapping a GR260 for a ZF

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • shiboujin
    R3VLimited
    • Feb 2006
    • 2791

    #16
    Nah I didn't I was legit asking. Pilot bearing would have been fun to miss.

    Status: HG repair. 488wtq though!

    Comment

    • FredK
      R3V OG
      • Oct 2003
      • 14745

      #17
      :giggle:

      Comment

      • samiam3356
        E30 Mastermind
        • Jul 2009
        • 1901

        #18
        hahaha my bad then, Just figured that you would have known that.

        Originally posted by Roysneon
        $5 shipped?
        Originally posted by MarkD
        You are a strange dude, I'n not answering any more posts from you.

        Comment

        • shiboujin
          R3VLimited
          • Feb 2006
          • 2791

          #19
          lol. Believe it or not, I don't know everything about E30s. Ixs scare me.

          Status: HG repair. 488wtq though!

          Comment

          • samiam3356
            E30 Mastermind
            • Jul 2009
            • 1901

            #20
            I don't believe it

            Originally posted by Roysneon
            $5 shipped?
            Originally posted by MarkD
            You are a strange dude, I'n not answering any more posts from you.

            Comment

            • FredK
              R3V OG
              • Oct 2003
              • 14745

              #21
              He knows enough to be dangerous, however.

              Q: What is Yoshi's favorite tool?

              Comment

              • shiboujin
                R3VLimited
                • Feb 2006
                • 2791

                #22
                Hammer

                Status: HG repair. 488wtq though!

                Comment

                • FredK
                  R3V OG
                  • Oct 2003
                  • 14745

                  #23
                  A: Sawzall

                  Can be used to set valve clearances, and in a pinch, to hog out intake ports on a cylinder head.

                  Comment

                  • shiboujin
                    R3VLimited
                    • Feb 2006
                    • 2791

                    #24
                    Actually, I've used an angle grinder for that.

                    Status: HG repair. 488wtq though!

                    Comment

                    • samiam3356
                      E30 Mastermind
                      • Jul 2009
                      • 1901

                      #25
                      Originally posted by shiboujin
                      Actually, I've used an angle grinder for that.

                      Was going to say that(actually did but deleted it.)

                      Originally posted by Roysneon
                      $5 shipped?
                      Originally posted by MarkD
                      You are a strange dude, I'n not answering any more posts from you.

                      Comment

                      • FredK
                        R3V OG
                        • Oct 2003
                        • 14745

                        #26
                        I thought you used the angle grinder and a flap disc to deck engine blocks?

                        Comment

                        • shiboujin
                          R3VLimited
                          • Feb 2006
                          • 2791

                          #27
                          Nah, thats sand paper and a wooden block. Start at 100 grit and work up to 2000.

                          Status: HG repair. 488wtq though!

                          Comment

                          • shiboujin
                            R3VLimited
                            • Feb 2006
                            • 2791

                            #28
                            FYI it needs to be a GR260 slave. The ZF one actually protrudes into the bell housing while just the plunger goes in on the GR260.

                            Status: HG repair. 488wtq though!

                            Comment

                            Working...