Announcement

Collapse
No announcement yet.

3.5" MAF to 3" Throttle Body?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    3.5" MAF to 3" Throttle Body?

    I guess I don't understand why you would have a 3.5" MAF going into a 3" throttle body. If the airflow is bottle necking at the TB then what is the benefit of running a bigger MAF if air flow is being reduced at the TB? Wouldn't you need a big bore TB? And if you would need a big bore TB then you would need to open the Intake Manifold hole also.

    I flunked physics so school me please.
    Last edited by ACHTUNG; 05-13-2011, 06:57 PM.
    1989 US E30 Cammed S52
    Under Construction: 1983 Euro E28 Cammed LQ9/LS3 Heads/Jakeb E28 LSx Kit


    #2
    You are right, they make little to no power.

    Comment


      #3
      I've done more interwebz searching and found some big bore TB like this:



      But then what do you do with the manifold? If you enlarge the intake mani does that mean worse low end torque?

      I need the optimal intake setup for a stock S52 converted to OBD1. Anyone?
      1989 US E30 Cammed S52
      Under Construction: 1983 Euro E28 Cammed LQ9/LS3 Heads/Jakeb E28 LSx Kit

      Comment


        #4
        Don't bother with a big throttle body. Just run the MAF your chip is tuned for and go for it.

        Comment


          #5
          Crap like this are generally gimmicks. Even CAIs don't really give you anything. Don't waste your money.

          Status: HG repair. 488wtq though!

          Comment


            #6
            well, I already wasted my money on a 540 MAF and the chip for it. Should have asked this question before I bought all my shit.
            1989 US E30 Cammed S52
            Under Construction: 1983 Euro E28 Cammed LQ9/LS3 Heads/Jakeb E28 LSx Kit

            Comment


              #7
              Would of been a great idea. But most people here just get the 540 MAF and chip, that's it. I did the same But like mention above, it's just a waste of moneyz

              Comment


                #8
                Originally posted by matt View Post
                Don't bother with a big throttle body. Just run the MAF your chip is tuned for and go for it.
                +1.

                I upsized the TB on my motor by 20%, from an M50 one to an M54 one.

                Gained ZERO on the dyno.

                Comment


                  #9
                  so..does this mean the miller MAF is a waste of money too?

                  Comment


                    #10
                    Originally posted by shiboujin View Post
                    Crap like this are generally gimmicks. Even CAIs don't really give you anything. Don't waste your money.
                    This. I probably wouldn't even have gotten my Kamotors kit if my M50 had come with an airbox.

                    Comment


                      #11
                      Originally posted by nwe30 View Post
                      so..does this mean the miller MAF is a waste of money too?
                      No.. that's different.

                      Comment


                        #12
                        that's like saying getting new rims is a waste of money since they serve the same functionality as stock ones. Just when you drive hard, you may see some gains.

                        Just like these mods. not for everyday boring drivers. I got my 3.5 at the junkyard for $9...why not.
                        '87 325ic, powered by S50.

                        Comment


                          #13
                          I got my 3.5 MAF for free at the junkyard, stole that shit like nothing :)

                          Comment


                            #14
                            why is the miller MAF a different story? What does it do that produces actual gains?
                            1989 US E30 Cammed S52
                            Under Construction: 1983 Euro E28 Cammed LQ9/LS3 Heads/Jakeb E28 LSx Kit

                            Comment


                              #15
                              in for a good reason for Millers MAF.
                              I got a fender roller now! LMK if you need me to roll your fenders or want to rent the tool from me locally.

                              Paypal: vdang5@gmail.com

                              Delta Auto Care
                              2875-C Towerview Road
                              Herndon, VA
                              703.435.1375

                              My Feedback Thread: Evil_Twin

                              Comment

                              Working...
                              X