Show your mufflers

[CAOSyAMOR]

^^^ These are 24V setups, not s14s....

Thread is titled 'Show us your mufflers'

Divert your eyes if I offend you.

[e30polak]

^^^ These are 24V setups, not s14s....

[CAOSyAMOR]

Before w DTM Style tips


After w SuperSprint Full SS Race Exhaust and 50/50 header

[e30polak]

Can't believe I haven't taken the opportunity to whore my exhaust up in this thread!

Old setup: Ebay headers > y-pipe > 3" piping > Accelerator 26" truck series muffler > 3" piping > Vibrant Street Power Turbo muffler

http://www.youtube.com/watch?v=j4YUuLrjBrw&feature=channel_page

New setup: Ebay headers > Flowmaster y-pipe > 2.5" piping > Borla center in/out 2.5" muffler > 2.5" piping > Vibrant Street Power Turbo muffler

http://www.youtube.com/watch?v=nS2RJCk_itY&feature=channel

http://www.youtube.com/watch?v=r2H5YreLZqk&feature=channel

There that's more like it! :p

[e30polak]

I got my car back today from MBS in Pasadena,MD. Its a little loud for my liking but i am going to give it some time..

2.5" SS
300 cell cat
magnapack resonator
magnaflow 18" muffler

It's loud because of the Magnaflow at the end. If you ran a Borla it would clean up the exhaust note and quieten it down. Or, you could put a second muffler in the middle instead of the resonator. That resonator isn't doing much for you as far as noise level.

I'll be doing the SS rep headers into a 2.5" single into a 18" x 8" oval Thermal Research and Development muffler.

That's gonna be loud as fuck!

I got Ebay headers, to a dual in dual out race cat, to a dual in dual out magnaflow 14385 muffler. Little raspy with no resonators.

It's the Ebay headers that's making it raspy. A Borla or Vibrant muffler would clean up the note quite a bit. The Magnaflow has a raspy sound to it because of the packing inside of it. Borla/Vibrant > Magnaflow any day!:woowoo:

[SamE30e]

I got Ebay headers, to a dual in dual out race cat, to a dual in dual out magnaflow 14385 muffler. Little raspy with no resonators.

[trackbball21]

They are not cheep! It was very close to $1k

That is a bit much, but is it worth it? I have the SS replica headers and they hang very low, that coupled with an e36 exhaust = cannot drive over any bumps at all. Doesn't help that it keeps scraping and knocked a hanger off.

How long did they take to do the whole thing?

[z31maniac]

I'll be doing the SS rep headers into a 2.5" single into a 18" x 8" oval Thermal Research and Development muffler.

[bostonbmw]

How much did that run you? I only ask because I am about to get mine done down in Dc, but I am just interested to see what their rates are.

They are not cheep! It was very close to $1k

[surebimmer]

Here is the Super Trapp setup i just got on my M3 S52 swap.






Raceland ebay headers, into full 3 inch with a Super trapp.

[trackbball21]

I got my car back today from MBS in Pasadena,MD. Its a little loud for my liking but i am going to give it some time..

2.5" SS
300 cell cat
magnapack resonator
magnaflow 18" muffler

How much did that run you? I only ask because I am about to get mine done down in Dc, but I am just interested to see what their rates are.

[bostonbmw]

I got my car back today from MBS in Pasadena,MD. Its a little loud for my liking but i am going to give it some time..

2.5" SS
300 cell cat
magnapack resonator
magnaflow 18" muffler









2 photos from MBS website

[PaintPro21]

OOPS! Missed it. Now I see it.

it's still too far back

[cbouchez]

^ Funny, I was looking throughout this whole thread looking for exhaust ideas, wondering if I would be able to use the E30 325i SuperSprint cat back I already have for a S52 swap.

Sounds great with my M20.. nice deep hum at low RPMs and a great sound at WOT.

Very nice! I'm thinking about upgrading mine with the Ireland Eng. I was hoping I could use the same exhaust once I do an engine swap in the future.

I like the Super Sprint exhaust, it looks nice and I bet it sounds good, I have to look around for the sound clip.

[Mr Two]

http://forums.bimmerforums.com/forum/showthread.php?t=1148674&page=10

I was thinking about getting a set of these, and seeing as how both these headers and the UUC System U I'm running are 60mm piping, running a dual 60mm midsection, no cats or resonators.

The only thing I'm worried about is fitment. I've heard US spec headers are a tight squeeze, and these are euros.

I'm running treehouse eyeball arms, so I'm thinking I'll be in the clear.