S54 no start issue

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • said
    Member
    • Jul 2006
    • 61

    #1

    S54 no start issue

    Hi Guys!

    i have a swaped s54 into my e30. I've had troubles with the dme, flashing it, etc...

    finally, i bought a perfectly flashed dmd from frank smith, but my car only start when i spray fuel into the TB, then it runs perfect, idles great and keeps running!

    I have 1 bosch 044 pump which is priming on ignition and when cranking, my FPR gauge reads 5 bar when cranking, so there is fuel, but no injectors opening on start up....

    CPS is New and Cam sensors are new too...

    any idea on what could it be?

    thanks!
  • DesertBMW
    E30 Enthusiast
    • Aug 2011
    • 1011

    #2
    That is EWS block. on mss54 it blocks the injectors only and it will run if you spray starting fluid. There is also relay only for injectors.

    Comment

    • said
      Member
      • Jul 2006
      • 61

      #3
      Mmm... But the ecu was flashed to run on my e30.....

      ????? What can i do!!

      Comment

      • DesertBMW
        E30 Enthusiast
        • Aug 2011
        • 1011

        #4
        Originally posted by said
        Mmm... But the ecu was flashed to run on my e30.....
        !!
        porque estas tan seguro

        Comment

        • nando
          Moderator
          • Nov 2003
          • 34827

          #5
          did frank give you a cable for flashing?
          Build thread

          Bimmerlabs

          Comment

          • said
            Member
            • Jul 2006
            • 61

            #6
            he did... but i preferred that he flashed the ECU on site and the shipped it to me... since i was in peru, i though that was the best way..

            Comment

            • nando
              Moderator
              • Nov 2003
              • 34827

              #7
              if you have a cable he should be able to update it remotely. I doubt he forgot to turn off EWS, but maybe it wasn't communicated properly.
              Build thread

              Bimmerlabs

              Comment

              • said
                Member
                • Jul 2006
                • 61

                #8
                I do have a cable....

                Ill see what he says, if he tested the ecu before shipping, then i dont know what to say...

                Comment

                • nando
                  Moderator
                  • Nov 2003
                  • 34827

                  #9
                  just ask him if the EWS was turned of and if not I'm sure he can fix it
                  Build thread

                  Bimmerlabs

                  Comment

                  • said
                    Member
                    • Jul 2006
                    • 61

                    #10
                    just noticed that if i turn ignition off and on again, sometimes it will start...

                    so its not EWS for sure... but there something there, it should start ALWAYS, not randomly

                    any ideas?

                    Comment

                    • The Dark Side of Will
                      R3VLimited
                      • Jun 2010
                      • 2796

                      #11
                      Originally posted by said
                      finally, i bought a perfectly flashed dmd from frank smith, but my car only start when i spray fuel into the TB, then it runs perfect, idles great and keeps running!
                      Are you saying that it starts with starting fluid, but then keeps running on its own?

                      Comment

                      • nando
                        Moderator
                        • Nov 2003
                        • 34827

                        #12
                        Originally posted by said
                        just noticed that if i turn ignition off and on again, sometimes it will start...

                        so its not EWS for sure... but there something there, it should start ALWAYS, not randomly

                        any ideas?
                        it's doing that because it's priming the fuel pump and injectors.

                        it would not run on it's own if it was EWS though, I missed that.
                        Build thread

                        Bimmerlabs

                        Comment

                        • said
                          Member
                          • Jul 2006
                          • 61

                          #13
                          So... still having start issues... car will start after turning the ignition about 5 times.. weird huh?

                          this time im suspecting on the clutch switch, since my car is a pure race one, i don't have any switch down there, and i know m3's needs to press the clutch for the engine to start... my starter turns, since its wired directly, but should i feed the clutch signal on the ECU? now.. its ground or 12v? can't really understand the diagrams!

                          thanks for the help!

                          Comment

                          • nando
                            Moderator
                            • Nov 2003
                            • 34827

                            #14
                            you don't need a clutch switch for an S54 swap. the only way it would stop the car from starting is if you'd installed the entire EWS system.
                            Build thread

                            Bimmerlabs

                            Comment

                            Working...