N52 engine mounting (Z4 arms)

[adam.nonis]

Hi all,

I have been searching for the AKG Motorsport poly mounts, but they seem out of stock and on backorder everywhere.
Are there any alternatives? I would rather not use the aluminium version of the AKG mounts.

I'm running the Garagistic 24V swap mounts. Stiffer than I wanted, but they're fine for now. Doesn't seem too difficult to swap later.


Sent from my iPhone using Tapatalk Pro

[Striker01]

Maybe the upside-down hydraulic mount hack? (forgot who invented it...)

It moves the engine back 1/2" or so as well.

Which mounts are you referring to?

[hoveringuy]

Hi all,

I have been searching for the AKG Motorsport poly mounts, but they seem out of stock and on backorder everywhere.
Are there any alternatives? I would rather not use the aluminium version of the AKG mounts.

Maybe the upside-down hydraulic mount hack? (forgot who invented it...)

It moves the engine back 1/2" or so as well.

[blums_work]

Hi all,

I have been searching for the AKG Motorsport poly mounts, but they seem out of stock and on backorder everywhere.
Are there any alternatives? I would rather not use the aluminium version of the AKG mounts.

[hoveringuy]

I have the e90 2006 manual transmission

Good to go!

[1984Bmwe30]

I have the e90 2006 manual transmission

[hoveringuy]

What transmission did you used was it the stock 90
manual transmission that came with the N52?

I used the GS6-17 that came with it out of a 2010 328i.

Unlike most of the other DOHC swaps, the G-260 won't work, bellhousing different.

[1984Bmwe30]

Just curious I'm doing a swap of my own as well.

[1984Bmwe30]

What transmission did you used was it the stock 90
manual transmission that came with the N52?

[hoveringuy]

Hey guys I'm in the early stages of planning my N52 engine swap. I want to create a bit of a cruiser - something that's got plenty of power but not going to rattle me to pieces. Do you think that there is enough room to run a rubber engine mount with this set up? Cheers

I'm on rubber mounts. The Noise, Vibration, Harshness is not as good as E90 hydro mounts, but it's not bad like poly, either.

[CarlKB]

Hey guys I'm in the early stages of planning my N52 engine swap. I want to create a bit of a cruiser - something that's got plenty of power but not going to rattle me to pieces. Do you think that there is enough room to run a rubber engine mount with this set up? Cheers

[Striker01]

Here is a comparison of the driver's side mounts on the subframe.



Here are the crankshaft to frame rail measurements. Much better!




The transmission mount lifted right up onto its studs, without a fight. If you use these AKG transmission mounts you will have to enlarge the holes in the mount and the ears on the transmission.

[Striker01]

I would recommend using the AKG 24v mounts with this swap. I don't know what other brands may work but I know for sure that the Revshift ones do not, they will shift the front of the engine too far towards the intake side.

Here are the measurements after installing them.



The crank is much closer to the driver's frame rail and I had to pry the transmission quite a bit to get it mounted.


AKG poly mounts are not available for about 6 weeks so I ordered aluminum ones to use for mocking exhaust stuff up. AKG told me that the geometry is the same between the two.

They are symmetrical, the revshift ones are not.



Here is the driver's side revshift compared to the AKG.



Here is the passenger side comparison.

[hoveringuy]

Did you use NW Driveline? If so, what location? I've had less than stellar results with the Seattle location...

Yep, Seattle location. I had one go-back issue where the rear yoke wasn't e30 and needed to be turned. The nice thing is that when I moved the engine back that little bit they shortened the shaft and rebalanced for pretty cheap. (stock shafts can't be shortened, I guess..)

[iansane]

Did you use NW Driveline? If so, what location? I've had less than stellar results with the Seattle location...