N52 Swap

[moatilliatta]

Wow!

[James Crivellone]

This topic needs to be in the N54/N52 section. Thanks!

Moved!

[LukeJ]

This topic needs to be in the N54/N52 section. Thanks!

[TR6]

Can anyone provide me with the total height of the N52 (oil pan bottom to highest point)--or if it is any taller than the S52? I'd like to drop the N52 in my Triumph TR6 to drop weight and reduce steering effort at low speeds--no power steering in a TR6. The other measurement that would be helpful is width from intake boot to center of engine. The S52 intake boot is up again my master cylinder and wheel arch--see picture.
BTW great install CWLO.

[Mbeeng]

Was that a private message.
was meant to go on the thread
this is new to me

[Mbeeng]

Hello most cunning and industrious people. I entered this thread maybe six months ago with e46 compact swap aspirations. Back here now the owner of a unmolested e36 323i coupe for my new roadcar build
not of catching up to do.you have been busy
First up is to find relevant information regarding to pr not to delete dme
So I can get a parts list formulated
z43

[cwlo]

Car has been running great for a few years now.

There is also a successful N54 swap where the owner modified the subframe to allow the steering rack to sit forward enough to allow the oil pan to remain untouched. Definitely the way to go if it doesn't upset the steering geometry too much.

[m52boi]

Any updates on OPs swap?

[The Dark Side of Will]

I don't think the mechanical aspect of the swap has ever been a mystery.

[tbp88]

As far as I know the E36ti models have very similar rear suspension to the E30, but the front end is a lot more like the E36, which in turn is a lot more like the E46 - so the swap from a Z4 wouldn't be too challenging?

Still no clue on how hard/easy getting the N52 into the E30 was for CWLO :P

[Motheye99]

https://www.bimmerforums.com/forum/showthread.php?2346039-First-N52-Swap-1997-AlaskaBlau-E36-318ti-N52-6Spd

Has anyone read this thread? the 318ti is pretty similar to E30

[cwlo]

Yes, the 6 speed from the 330i. You need the front driveshaft section from a z4, and rear from the e36 M3 Automatic. You are correct in that the stock e30 will not fit the output flange of trans. The shift rod needs to be shortened, and slightly clocked over...like 15 degrees. Best way is to cut the rod to length, and then tack together to set the proper clock degrees you need for your application....then complete welding once its set up properly. There is someone who sells this item as we. If you search for e30 6 speed swap, you'll find any more info you need. For diff ratio, I recommend the 3.25 or 3.46.

[Saturnblau]

cwlo I’m assuming you used the ZF 6 speed (GS6-37BZ)? Do you mind telling me about the propshaft/guibo size? I believe it’s a 96mm output flange on the trans and e30 prop is a 78mm?


edit: looked back and saw the Z4 front and e36 rear. Will have to use forcedfirebird’s idea of a frankenshaft because I won’t be able to find an auto m3 shaft in the UK.

[LukeJ]

I started writing up a guide, but most of the info is in this thread. I am running it with the stock dme so there is no exotic tuning required. I got the ews deleted by nando, or you can install with cas and key.

Maybe just a 'parts list' would be helpful? This thread does contain everything, but having 'one location' for all the 'bits' you used would be awesome.

Thank you for sharing your knowledge and experience with this N52 swap. I bought my E30 with the N52 in mind, because of this thread.

Luke

[kristov]

Here are a few pics. Still need to finalize the wiring and a few other bits, but mostly complete.

I will do a write up of the whole swap while its still somewhat fresh in my head. What is the best way to create a fairly long thread on this forum?

Any idea on when you will do the write up?