Announcement

Collapse
No announcement yet.

iX wheel thread

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Stevo-iX
    replied
    By look like that do you mean height?
    Then no, you would need some different springs for that. Shocks just control dampening.

    Leave a comment:


  • 88e30ix
    replied
    Originally posted by nando View Post
    the only konis they sell for the ix are single (rebound) adjustable
    Sorry for the noob questions but if I do get the Konis my IX would look like that?

    Leave a comment:


  • nando
    replied
    the only konis they sell for the ix are single (rebound) adjustable

    Leave a comment:


  • 88e30ix
    replied
    Originally posted by two240s View Post
    16x7.5 et20 and 16x9 et15. 205/45/16 all around. Rear plastics arches are trimmed underneath and fenders rolled. Fronts clear fine. H&R sports/Koni adjustables.


    Where did you get those Koni capable of being adjusted?

    Leave a comment:


  • jmenacker
    replied



    O.Z. Graphite Chrono 16x7 et37

    These were replacements for a set of Mille Miglia MM-II's that were "permanently" borrowed. These have a harder look and are not as easy to clean. On the good side they are lighter than the MM's and haven't been curbed - yet. Available at Tire Rack for $200 a pop. S-Drive tires are excellent!

    Joe M in WV

    Leave a comment:


  • 325ix
    replied
    Could the flares be rolled 10mm to make them fit?

    Leave a comment:


  • nando
    replied
    no that won't even fit

    on a 7" wide wheel at ET24 you would need to roll the fenders, at ET10 you'd be sticking out ~10mm past the flares..

    Leave a comment:


  • 325ix
    replied
    Cool thanks. I have one more question. Would a 15x7 et 10 work with 205/50/15 tires? I'm new to wheels and what fits so I really have no idea how to know. Thanks again for answering all my questions. :mrgreen:

    Leave a comment:


  • nando
    replied
    it's likely, yes.

    if you really don't want to roll them, stick with 205/50s and a 10mm spacer.

    Leave a comment:


  • 325ix
    replied
    would a 10mm spacer and 225s require fender rolling? I like the wider tires but I don't really want to roll my fenders

    Leave a comment:


  • nando
    replied
    they will fit directly, but be far inside the fenders like stock. with a 10mm spacer you could run a 225/45-16, or a 15mm spacer for 205/50-16. if you want to push them out though you'll have to roll the rear fenders & trim the underside of the lips.

    Leave a comment:


  • 325ix
    replied
    I just found a set of Drag dr-16s. They are a 16x7 in. wheel with a 40mm offset. What size of spacer would be required front and rear? Also what size of tire would you reccomend? Thanks so much for answering all of my questions.

    Leave a comment:


  • nando
    replied
    ET38 is probably too high. you would likely need a spacer up front to clear the strut. my ET36 wheels have a 3mm spacer to clear the brakes, and the tire is really close (granted they are much wider than usual).

    try between ET35-ET30

    Leave a comment:


  • 325ix
    replied
    Ok so more like an 8 inch et38 and I wouldn't have to run streched tires?
    What are some 8 inch wheels with a lip that would fit? I'm partial to the sportmax 002 style I'd just rather have an 8 inch wheel.
    Thanks
    Last edited by 325ix; 10-06-2009, 02:44 PM. Reason: add stuff

    Leave a comment:


  • nando
    replied
    Originally posted by 325ix View Post
    Thanks so would a et15 work ona 8 inch wheel? And what tire size should be used? I can't stand stretched tires on an 8 inch wheel.
    not a snowballs chance in hell without seriously stretched tires (maybe 195s at most).

    double that number and you'll be closer..

    Leave a comment:

Working...
X