Announcement

Collapse
No announcement yet.

The Cabrio Suspension Thread

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • N2MYE30
    replied
    Originally posted by e304lyfe View Post
    Thanks Barry! E28 M5 rims. Genuine m-technic 5-speed. I believe there is only one size upper rear spring pad available. I considered doubling them up though.
    pulled from realoem

    15 SPRING PAD7,5MM 233531136386 $7.62 ONLY APPLIES TO COIL SPRING WHITE
    15 SPRING PAD5MM 233531136385 $6.70 ONLY APPLIES TO COIL SPRING RED
    15 SPRING PAD10MM 233531136387 $8.28

    Leave a comment:


  • N2MYE30
    replied
    Originally posted by reelizmpro View Post
    I would run extra thick pads on top, in the back to bring it up some and give the springs more travel. Looks great by the way.
    I was gonna do this exact thing on mine. Maybe 10mm instead of the stock 5mm.

    Leave a comment:


  • e304lyfe
    replied
    Originally posted by reelizmpro View Post
    I see what you did there. E28 M5 or evo wheels? Genuine M Technic? I would run extra thick pads on top, in the back to bring it up some and give the springs more travel. Looks great by the way.
    Thanks Barry! E28 M5 rims. Genuine m-technic 5-speed. I believe there is only one size upper rear spring pad available. I considered doubling them up though.

    Leave a comment:


  • reelizmpro
    replied
    Originally posted by e304lyfe View Post
    e30 m3 suspension
    I see what you did there. E28 M5 or evo wheels? Genuine M Technic? I would run extra thick pads on top, in the back to bring it up some and give the springs more travel. Looks great by the way.

    Leave a comment:


  • e304lyfe
    replied
    Originally posted by CorvallisBMW View Post
    M3 5-lug or e36?
    e30 m3 suspension

    Leave a comment:


  • CorvallisBMW
    replied
    M3 5-lug or e36?

    Leave a comment:


  • e304lyfe
    replied
    Originally posted by N2MYE30 View Post
    I agree but I wouldnt kick it outta the garage for it. Do you have a 5-lug swap e304lyfe? Those are 16", right?
    Yes, the car is 5 lug, and they are 16's.

    Leave a comment:


  • CorvallisBMW
    replied
    After looking at that car, I'm suddenly a little sad I dropped $400 on GC coils to get the same stance as $250 H&R Race :(

    Leave a comment:


  • N2MYE30
    replied
    Originally posted by CorvallisBMW View Post
    Looks great! E90 drop hats would make it 100% perfect IMO.
    I agree but I wouldnt kick it outta the garage for it. Do you have a 5-lug swap e304lyfe? Those are 16", right?

    Leave a comment:


  • e304lyfe
    replied
    Originally posted by CorvallisBMW View Post
    Looks great! E90 drop hats would make it 100% perfect IMO.
    Thanks. .......I don't know about the car being much lower and being practical.

    Leave a comment:


  • CorvallisBMW
    replied
    Looks great! E90 drop hats would make it 100% perfect IMO.

    Leave a comment:


  • e304lyfe
    replied
    Swapped my vert to h&r race and bilstein sports late last season. Sold on it being a suitable setup for a vert. It could be a bit stiffer in the rear. All OE but added the largest lower spring pad in rear.

    Leave a comment:


  • mach schnell
    replied
    Originally posted by mattdk318i View Post
    if you read through this thread its discussed many time. Thus a thread for nothing but cabrios
    Actually, it's not. There really is not a good clean low setup shown. There are plenty of hacked together combos (cabrio fronts, coupe rears, this and that).

    I'm looking for a cabrio specific setup, not a combo of two different sets of springs, or springs intended for a non-cabrio E30. And I don't want Ground Control's.

    Leave a comment:


  • mattdk318i
    replied
    if you read through this thread its discussed many time. Thus a thread for nothing but cabrios

    Leave a comment:


  • mach schnell
    replied
    What are some good springs that will get a 'vert nice and low? As in, lower than H&R Sport's?

    Vogtland maybe? Any pics?

    Leave a comment:

Working...
X