DIY: Undo the bitch clip the easy way.

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • kid325e
    replied
    Dealt with this this last weekend. I ended up disconnecting the trans brace, and mounts, dropping the trans down enough to fit a screw drive under the clip itself and pulled towards me and POP, it came out!

    Leave a comment:


  • Philo
    replied
    Yeah, I have never had an issue with those clips. I've worked on more than a handful of e30s as well. Insert flathead screwdriver from the driveshaft side, pull down. It pops up without a fuss every time. Not even a 30 second event.

    Leave a comment:


  • bmwguy325is
    replied
    I used a small pry bar. Works every time. Next time ill run a stop watch.

    Leave a comment:


  • Vivek
    replied
    Originally posted by Danny
    I seriously could not get the bitch clip with screw drivers, I went at it for four hours straight until I said fuck it and bought this tool. After I came back, I got it done in 2 minutes.
    This was me yesterday. That tool's a life saver.

    And free bump for an old but extremely useful thread. This is one of those things that's really not obvious and it's not easy to figure out on your own, great DIY.

    PS: has anyone eliminated the bitch clip and stuck a bolt and nut through there for easier removal? I saw this in another thread.

    Leave a comment:


  • camshaftgsxr
    replied
    you guys have problems with that? all you need is a cool exhaust and a small short flat head

    Leave a comment:


  • E30 331is
    replied
    Originally posted by camshaftgsxr
    what is the bitch clip? are we talking the clips on the shift linkage?
    The ones on the shift linkage are circlips, this is the carrier arm clip that sits on top of the transmission.

    Leave a comment:


  • Thizzelle
    replied
    Originally posted by camshaftgsxr
    what is the bitch clip? are we talking the clips on the shift linkage?
    yes

    Leave a comment:


  • camshaftgsxr
    replied
    what is the bitch clip? are we talking the clips on the shift linkage?

    Leave a comment:


  • Mossman
    replied
    Sometimes they're really friggen tight and there's no way to slide any tool in between it and the top of the trans, and prying from the side just mangles it. Usually they're not too bad though and only take a couple minutes. It also really depends on whether you're yanking tranny so exhaust, driveshaft and heat shields are all out of the way and tranny mount is disconnected to drop it down a few inches, then you have plenty of access.

    Leave a comment:


  • Cloudbase
    replied
    This took my buddy and I well over an hour on an M Roadster we were doing and we destroyed the clip. Used this tool today and it took less than 5 seconds! Well done!!!!!!

    Leave a comment:


  • 2002maniac
    replied
    Usually it comes out pretty easy for me with a screwdriver, but on one particular car I could NOT get it off. took me 15 minutes and I was getting pretty frustrated. I can't imagine going at it for 3 hours!

    Leave a comment:


  • nando
    replied
    must be slightly different engine positions of E30s. I've never had it take longer than 5 minutes.

    Leave a comment:


  • J0nnyr0ck3t
    replied
    Never have I been able to remove this bitch clip in less than 3 hours. I even broke the SOB and bought myself another.

    Leave a comment:


  • frankenbeemer
    replied
    I was a miserable failure at the screwdriver technique, despite the rediculous number of screwdrivers I tried. Nice write-up!

    Leave a comment:


  • Danny
    replied
    I seriously could not get the bitch clip with screw drivers, I went at it for four hours straight until I said fuck it and bought this tool. After I came back, I got it done in 2 minutes.

    Leave a comment:

Working...