What 4x100 wheels will fit e30s?

[rwh11385]

http://www.r3vlimited.com/board/showthread.php?t=69071&page=2

check out my tight thread (created in search of wheels that were direct fit since my Koseis centering ring likes to stick on my hub... rusty old bastard.)

15x6.5" ET33. Work without spacers, hubcentric, but too close to the strut to run 225's.

but unforunately not sure if an ultra wide 205 like an r comp or an Azenis would work

I'm trying to buy the six and use them as daily driving wheels with 205's. No really reason for 225s unless going for the new RS-2s and Auto-X (and enjoy that cost!), and I'm just going to use Hoo-Hoos on baskets for that hopefully, so its all good.

If you don't want the limited selection of 205-60-14 on a set of basketweaves, it makes sense. Or just hold out for a set of 15x7 with an offset of ET27 to ET23 to fit 225s. If you want to run Toyo RA-1s eventually for SpecE30, baskets will work on a budget build with take-offs, or full meat on 15x7... anything from et30 to et17 should work. I never put R comps on my Koseis but 2002maniac has 225 Ziexs on his

[JRKOUPE]

I run K1's on 225/50.....15....RA 1's.....real closeto strutube.

hey rwh.....I use anti sieze on hub...helps a bit w/ getting rings off.

[rwh11385]

i used a lot of it and no luck. going full BBS correct hubcentric wheels from now on

gonna lose the track car look though with no more K1s =( hhaahahahha

[JRKOUPE]

i used a lot of it and no luck. going full BBS correct hubcentric wheels from now on

gonna lose the track car look though with no more K1s =( hhaahahahha

..are you getting soft ?......the rings can be a pita for sure. One day I was trying for like 45 min to get one off.


Do you drive car everyday?....


BBS are very pricey, no?....


seeling the k1's?...lemme know

[Digitalwave]

Plastic hubrings are where its at.

[JRKOUPE]

Plastic hubrings are where its at.

except I know a couple of tracked cars that melted the frt. plastic rings.

[rwh11385]

..are you getting soft ?......the rings can be a pita for sure. One day I was trying for like 45 min to get one off.


Do you drive car everyday?....


BBS are very pricey, no?....


seeling the k1's?...lemme know

When I had to get a new wheel bearing during school and had a shop do it, one flew off and cut the mechanic above the eye and he bled decent. I also broke 5 screwdrivers trying to get them off.

hahahhahaha. pricey? hahahhaa. :p

yes, daily driver

If I get these RZs I want, they are going to Will's brother.


Tirerack recommends metal rings if tracking

[s52e368]

another option

15x7
30mm ?


spacer = 5mm ?

[Erick]

Might be able to clear it.... my 15x7s are 27mm and it clears.

[Digitalwave]

5 or 10mm spacers would work.

[Erisa_1974]

another option

15x7
30mm ?


spacer = 5mm ?

15x7 et30 can fit without spacers... 205s are least. or a narrow 225 even.

they were on my car when i bought it

[Dave]

15x7 et30 can fit without spacers... 205s are least. or a narrow 225 even.

they were on my car when i bought it

Are you from Ohio? I swear I met an Erica Risa who runs an e30 BMW at some local auto-x events and she told me she shares it with her brother.

[Erisa_1974]

I dunno what you're referring to.... I'm not a girl and don't have a sister...shhh

[Dave]

I dunno what you're referring to.... I'm not a girl and don't have a sister...shhh

Well, maybe then you are a transvestite?

[Karlspackler]

http://cgi.ebay.com/ebaymotors/15X8-...QQcmdZViewItem

Hows about these? Euro style? Just for driving around / show wheels(not that I will be showing the car)

I will run K1's for auto-x with proper offset