M42 turbo fact thread

[shEck3lls0]

What size and how many CFM of a fan do you think I should get for my build? What are you running buttchug?

[318kid]

For oil feed and return, I ran a line from the oil pressure sender to a T with a VDO pressure sender and a line to the turbo. DO NOT mount all this to the engine; I broke 2 t's within a month just from the vibration, and it causes pretty instantaneous oil pressure loss. I got lucky and happened to see it happen both times. My setup is mounted remotely. Oil return is to a bung in the oil pan and to a bung welded to the dipstick tube. Don't just use a bung to the oil pan-because it's below the oil level in the pan, the drain will pressurize and blow the seals on the turbo. You don't want that.

I'm running an intercooler from a Volvo 740 TIc. It fits perfectly in front of the AC condensor once you remove the aux fan, so you can keep your AC.

Do you have any pictures? Also how do you think the m42 would handle 5psi with no engine management? I know the DASC is about 5 psi but do they offer a chip to go along with it?

[Victell]

Great thread. Good to have a bunch of info in one place. Subscribed

[gearheadE30]

I'm running a custom split-flow manifold with external WG mount and a Garrett T3 Super 60 with a 0.63 A/R turbine side. Full boost around 3k revs, and a bit of lag, but there is no power dropoff until somewhere past 7000 revs. 2.5" exhaust all the way back. Tial WG and a WyntonM BOV, 44mm. WyntonM bits are sold through ebay and are pretty cheap, but I've been absolutely thrilled with the quality and performance of this one. It's also pretty quiet and adjustable.

If you can find a Garrett TA31 turbo, I had one on the car for awhile. It makes full boost at 2500 revs, very little lag, but it peaks around 6000 revs. Fantastic little turbo, but they are somewhat uncommon.

For oil feed and return, I ran a line from the oil pressure sender to a T with a VDO pressure sender and a line to the turbo. DO NOT mount all this to the engine; I broke 2 t's within a month just from the vibration, and it causes pretty instantaneous oil pressure loss. I got lucky and happened to see it happen both times. My setup is mounted remotely. Oil return is to a bung in the oil pan and to a bung welded to the dipstick tube. Don't just use a bung to the oil pan-because it's below the oil level in the pan, the drain will pressurize and blow the seals on the turbo. You don't want that.

I'm running an intercooler from a Volvo 740 TIc. It fits perfectly in front of the AC condensor once you remove the aux fan, so you can keep your AC.

The engine is completely stock with the exception of a rebuilt head with shimmed valve springs for a bit more tension and ARP head studs. I'm running an M20 flywheel and clutch, with the flywheel machined to 13 lbs. No rattles, and factory driveability.

Engine management is MS2 extra, with a custom harness so I didn't have to hack the factory wiring. I'm actually using factory coils and coil drivers with sequential ignition and batch injection.

Estimated numbers are around 200 crank HP at 7.5 psi just based on driving similarly powered e30's, and it hasn't been on a dyno yet. Next spring/summer the boost will be upped to 10 psi and will be taken to a dyno shop.

So far I have almost 15k miles on the turbo with no issues.

Edit: a few more things
I'm using 2.5" IC piping.
Injectors are 43 lb/hr bosch green tops from Ford Racing. FR flow matches their injectors.
MAP sensor and IAT sensors are from GM; MS works with all of the other BMW sensors.

[blueapplesoda]

I do m42 standalone engine management setups. Same price as the m20 options, just with a custom 88pin DME box. Full sequential is possible on ms2/ms3 setups, however the fuel injector harness must be modified for full sequential fuel injection. Prices range from $700 on up. Base tune is included.

This one was a 403 donor ECU converted to MS. The purple wire, if you look closely is labeled 2-step. It is for customer requested launch control. On the left there is a serial port, and the right there is a MAP sensor port. Removes the MAF :)




Derek
DedericMS

[Good & Tight]

I make custom top mounts for the M42.

Pricing and details here---> http://www.r3vlimited.com/board/showthread.php?t=224115

[Dj Buttchug]

Now that we have a good number of people with turbo 4 cyl engines this thread will combine all the FACTS in one place. M42 only! New builds, old builds, newbies and dreamers all welcome. Let this be an open discussion to anything and everything related to turbo 318.

Post specs, pictures, builds, turbos, videos, links and tuning options.Share your experience.Be specific and thorough. Share your experience so others can learn from you.

Ill start.


91 M42 B18
Garret GT2871RS ball bearing turbo oil and water cooled.
Forged CP pistons 8.5:1, Stainless rings. 85 mm overbore
Balanced bottom end
360 degree oil well bearings
Stock head gasket
Full ARP fastening hardware (connecting rod bolts, main studs and head studs)
3inch turbo back full custom exhaust no cat no resonators, 24" series truck muffler.
modified m5x turbo manifold (obx, Cxracing, ebay)
3 inch intercooler piping
Megasquirt
1000cc injectors High imp
GM style Intake air temp sensor
Obx vacuum port
Apexi electronic boost controlled wired to MS
16psi controlled yields and estimated 260 whp. (stock clutch and flywheel cannot handle it)


before AFM delete

oil feed for turbo