m20b27 engine stuttering and holding back, temperature jumps

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • MWe
    Noobie
    • Feb 2026
    • 14

    #1

    m20b27 engine stuttering and holding back, temperature jumps

    Currently experiencing a problem with my engine.
    It is a m20b27 stroker with 1.3 moronic.

    When driving the engine sometimes stutters, most noticeable during acceleration, but during constant speed it sometimes feels like it's holding back as well.
    Engine does manage to pull through the revs but a half gas it's worse than when I floor the throttle.
    During this stuttering the temperature needle spikes to about 3 quarter, so just before the red area, but the strange thing is that is jumps to high instead of creeping.
    Another strange thing, when I shift gear, the temperature jumps back to the middle sometimes.
    With no load the engine revs freely.

    I suspect a fault in the engine loom, a shortage or bad connection, but maybe someone has experienced similar problems.
    Anyone has a clue to where to look first?
  • redlightpete
    Wrencher
    • Mar 2012
    • 266

    #2
    Check the circular connector under the intake manifold. It contains the injector wiring and the temp sensors, so when the engine is moving under load, you’ll get intermittent misfires and temperature readings. Coolant leaks at the throttle body tend to leak onto this connector and corrode it.

    Comment

    • MWe
      Noobie
      • Feb 2026
      • 14

      #3
      Currently checking that one indeed, plug c191 it’s called I think.
      Had the similar feeling that might be it but maybe someone experienced the same problems and knows the direct solution.
      Last edited by MWe; 11-02-2026, 06:49 AM.

      Comment

      • MWe
        Noobie
        • Feb 2026
        • 14

        #4
        So that plug was cleaned en reassembled, didn’t see much dirt in there. Problem still ongoing unfortunately.
        Easy on the gas seems to work, full throttle also less holding back. At half gas or slightly accelerating the problem is most noticeable. My suspicion is the AFM now

        Comment

        • zaq123
          E30 Mastermind
          • Jul 2016
          • 1571

          #5
          I still think it's C191 connector, main harness side or injector harness side. Fueling issues and temp sending unit issue at the same time, gotta be c191. How did you check it? As a min, I'd put ignition on and go bending moving harness around and have someone else watch if it affects the temp gauge, move c191 around including that small wire from the harness to the temp sending unit and temp sensor.

          Comment

          • MWe
            Noobie
            • Feb 2026
            • 14

            #6
            I was about to take a look at the AFM but did the same test as you described when somebody was nearby.
            So with the car running I had the other person looking at the temp gauge on the dash and I wiggled on the connector a bit, pushed in the rubber grommet as well, and the temp gauge went berserk.
            So currently in the process of replacing that connector with a DT-connector. I went with and DT04 8p version because I thought there were 7 wires, apparently there are only 6.
            So the red/white cable, feeding all 6 injectors, will get two wires.
            Click image for larger version

Name:	IMG_2048.jpg
Views:	21
Size:	133.1 KB
ID:	10169672
            The harness is a bit short, so I went with a pigtail.
            Hopefully I get it fixed this week, will report back if it solved my problems.

            Comment

            • MWe
              Noobie
              • Feb 2026
              • 14

              #7
              So this is fixed now.
              I've replaced the c191 connector with a DT connector and the problems seem to have disappeared.
              Temperature gauge does not jump anymore, so that's a clear sign for me it was related to the connector.

              I disconnected the battery before I started working on the connector, so the motronic 1.3 lost it's data and was reset to factory settings.
              It's a 2.7 with higher CR and a schrick 272 cam with different injectors, so the base mapping of the motronic 1.3 does not work nicely from the start.
              This resulted in it running a bit lean or rich the first hour, but eventually the ecu started to relearn and adjust it's mapping (that's my theory).

              Strange sensation that relearning process, you do a pull and it bogs down the first try, then you do another pull and it still doesn't feel right, and after a few tries it manages to pull at full power without hesitation.

              Am I correct in assuming that the ecu now reprogrammed itself? (until I take the battery out for 10 minutes)

              I need to test drive again to see if all is well now, but they started to put salt on the roads last weekend, so I have no intention to drive the car before we have some rainy days.

              Click image for larger version

Name:	IMG_2056.jpg
Views:	0
Size:	145.3 KB
ID:	10169926

              Comment

              • zaq123
                E30 Mastermind
                • Jul 2016
                • 1571

                #8
                make sure your CID from cyl6 plug is connected. Otherwise M1.3 fires 6 injectors all the time unlike only at the startup. CID syncs the home signal after a startup and M1.3 switches to fire only 3 inj at a time for a normal operation. There isn't really any relearning going on. If it runs rich, maybe your coolant sensor (blue one) or it's connection isn't good, ecu thinks engine is cold giving it more fuel than it needs when warms up
                Last edited by zaq123; Yesterday, 07:06 PM.

                Comment

                Working...