Installing New Suspension

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Danny
    Moderator
    • Feb 2008
    • 14217

    #16


    Another tip, use a floor jack to put pressure on the control arm at the ball joint. This will help you loosen the nut.

    Comment

    • Danny
      Moderator
      • Feb 2008
      • 14217

      #17
      Is the nut turning with the ball joint? Or just not turning at all?

      If it isn't turning at all you may need to apply some heat. This may adversly affect the rubber boots around the ball joint.

      Comment

      • bigdrick323
        Mod Crazy
        • Feb 2012
        • 616

        #18
        nut doesnt budge....
        sigpicMy Project!

        Official North Texas Bimmers Club E30 Representative

        www.BimmerAlliance.net

        "If you have questions about events or need help in the DFW area don't be afraid to contact me."

        Comment

        • Danny
          Moderator
          • Feb 2008
          • 14217

          #19
          Did you try any of the things I suggested?

          Comment

          • willworkfore30s
            E30 Enthusiast
            • Aug 2011
            • 1090

            #20
            Get more leverage on the wrench with a pipe or something.
            sigpic

            Comment

            • bigdrick323
              Mod Crazy
              • Feb 2012
              • 616

              #21
              Originally posted by Danny
              Did you try any of the things I suggested?
              Yes, except for heat, I don't have a torch or anything. Not sure how I would heat it up, hairdryer? I will try to do the jack, but I'm concerned about putting too much pressure on the joint.
              sigpicMy Project!

              Official North Texas Bimmers Club E30 Representative

              www.BimmerAlliance.net

              "If you have questions about events or need help in the DFW area don't be afraid to contact me."

              Comment

              • Danny
                Moderator
                • Feb 2008
                • 14217

                #22
                If you jack it up a bit it won't hurt anything, it will just make the ball joint seat fully so that it won't spin. If you can't even get the whole joint to spin though you made need to do as "willworkfore30s" suggested and use a cheater bar.

                Comment

                • bigdrick323
                  Mod Crazy
                  • Feb 2012
                  • 616

                  #23
                  Damn, no cheater bar....
                  sigpicMy Project!

                  Official North Texas Bimmers Club E30 Representative

                  www.BimmerAlliance.net

                  "If you have questions about events or need help in the DFW area don't be afraid to contact me."

                  Comment

                  • bigdrick323
                    Mod Crazy
                    • Feb 2012
                    • 616

                    #24
                    Going to try again when I get home, but I have bad feeling about nut. I can at least remove passenger side.

                    I am away from my computer, being lazy!
                    sigpicMy Project!

                    Official North Texas Bimmers Club E30 Representative

                    www.BimmerAlliance.net

                    "If you have questions about events or need help in the DFW area don't be afraid to contact me."

                    Comment

                    • Danny
                      Moderator
                      • Feb 2008
                      • 14217

                      #25
                      Find a friend with an impact.

                      Comment

                      • bigdrick323
                        Mod Crazy
                        • Feb 2012
                        • 616

                        #26
                        I have an impact but as I mentioned earlier I cannot seat it on the bolt. Too much stuff in the way

                        I am away from my computer, being lazy!
                        sigpicMy Project!

                        Official North Texas Bimmers Club E30 Representative

                        www.BimmerAlliance.net

                        "If you have questions about events or need help in the DFW area don't be afraid to contact me."

                        Comment

                        • IronFreak
                          No R3VLimiter
                          • Dec 2012
                          • 3702

                          #27
                          Use the jack handle as a cheater bar
                          sigpic

                          Rebellion Forge Custom Fabrication

                          1988 325is - TrackRat in progress

                          Instagram @rebellionforge

                          Comment

                          • bigdrick323
                            Mod Crazy
                            • Feb 2012
                            • 616

                            #28
                            The socket wrench is too big for Jack handle unfortunately.

                            I am away from my computer, being lazy!
                            sigpicMy Project!

                            Official North Texas Bimmers Club E30 Representative

                            www.BimmerAlliance.net

                            "If you have questions about events or need help in the DFW area don't be afraid to contact me."

                            Comment

                            • Danny
                              Moderator
                              • Feb 2008
                              • 14217

                              #29
                              Use an extension on your impact... This isn't rocket science.

                              Comment

                              • dude8383
                                Forum Sponsor
                                • Jan 2005
                                • 10387

                                #30
                                Originally posted by bigdrick323
                                I have an impact but as I mentioned earlier I cannot seat it on the bolt. Too much stuff in the way

                                I am away from my computer, being lazy!
                                Is that your fucking signature?
                                IG: deniso_nsi Leave me feedback here

                                Comment

                                Working...