Offset for stupidly wide wheels?

[808BMW]

What offset is needed to have a 10" wide wheel up front with no (or as little possible) rubbing. Only the inside matters, fender clearance is not an issue.

How about 12" out back? again, inside only, fenders don't matter.

[kylebes1]

you plan on steering with those 10" wheels in front?

[M-technik-3]

8" maybe with varying degrees of fitment. 10" I just don't seeing it happening.

[Ryan Stewart]

It would have to be super low, like 5. That is if fender clearance was a non issue, youd need one hell of a widebody.

Dunno about the 12" though, my 8" run pretty dam close in et28

[qimis]

i was driving around for a day until i noticed that the guy putted my 10x16 at the front and 9.5x16 at the back only on one side. :nice:

[M-technik-3]

What kind of shop did that? I won't let shops touch my BBS. I do them myself, ie Mounting and Balancing.

[808BMW]

i was driving around for a day until i noticed that the guy putted my 10x16 at the front and 9.5x16 at the back only on one side. :nice:

Rubbing with 10's up front? What's the offset on your RS's anyway?

[royalflush313]

i was driving around for a day until i noticed that the guy putted my 10x16 at the front and 9.5x16 at the back only on one side. :nice:

wow..

What offset are you running, and what size adapters are you using? 25mm?

[qimis]

What kind of shop did that? I won't let shops touch my BBS. I do them myself, ie Mounting and Balancing.

it was a body shop where i got my car from and installed the mtech 2 kit. hehe lucky you ... you can balanced it your own.

i was driving around for a day until i noticed that the guy putted my 10x16 at the front and 9.5x16 at the back only on one side. :nice:

Rubbing with 10's up front? What's the offset on your RS's anyway?

didn't rub, i had the front just less than 1" gap b/w fender and tire. probably it will rub if it's lower than that.

i was driving around for a day until i noticed that the guy putted my 10x16 at the front and 9.5x16 at the back only on one side. :nice:

wow..

What offset are you running, and what size adapters are you using? 25mm?

front: ET 5, w/ 25 mm adapters
rear: ET 3, w/ 20 mm adapters

[Digitalwave]

What kind of shop did that? I won't let shops touch my BBS. I do them myself, ie Mounting and Balancing.

it was a body shop where i got my car from and installed the mtech 2 kit. hehe lucky you ... you can balanced it your own.

i was driving around for a day until i noticed that the guy putted my 10x16 at the front and 9.5x16 at the back only on one side. :nice:

Rubbing with 10's up front? What's the offset on your RS's anyway?

didn't rub, i had the front just less than 1" gap b/w fender and tire. probably it will rub if it's lower than that.

i was driving around for a day until i noticed that the guy putted my 10x16 at the front and 9.5x16 at the back only on one side. :nice:

wow..

What offset are you running, and what size adapters are you using? 25mm?

front: ET 5, w/ 25 mm adapters
rear: ET 3, w/ 20 mm adapters

So you the rims in the front are ET30, with 25 mm spacers, or are they effectively ET -20mm?

[Mystikal]

-20.

[qimis]

nope, there's more complicated calculation behind it. those offset that i posted are final offsets.

[royalflush313]

^^ Qimis, what kinda suspension are you running, and your fenders modded?

[qimis]

i'm running on KW Variant 1.
fenders were rolled to the max. :mrgreen:

[E30_boy]

I had KW V2's on my Jetta, I wanted to get a set for the Bimmer but my KW dealer here says there is no listing for E30 :? Also did they make RS's 4x100 in 16"? I'v only seen 15" RS' in 4x100