Announcement

Collapse
No announcement yet.

1988 E28 on Accuair

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    1988 E28 on Accuair

    1988 528e
    162,000 plus miles on chassis
    12k without Rotiforms/15k with. Also considering trades.
    Located in Houston, Texas & can arrange for shipping at the buyers expense.


    ENGINE
    - M20B27 in-line 6 cylinder
    - ā€˜Iā€™ head with 885 casting & dual valve springs
    - ā€™Iā€™ camshaft
    - Larger intake & exhaust valves
    - Extrude honed intake manifold to increase airflow & upgraded to a larger throttle body to accommodate airflow
    - Upgraded harness & ECU to 173 Motronic with performance chip
    - Valve adjustment, manifold gasket replacement, fuel injection cleaning, powder coating & throttle body polishing performed 12/2013
    - Compression numbers 164, 163, 162, 164, 164, 162 performed 12/2013.
    - New cap, rotor, performance ignition wires, Bosch silber plugs less than 6000 miles ago.
    - Synthetic 20w-50 or 10w - 40 always used.


    DRIVE LINE
    - Clutch set, giubo, u-joints & center support bearing replaced less than 6000 miles ago.
    - Lightweight single mass fly wheel replaced less than 8000 miles ago.
    - LSD 3.73 installed than 8000 miles ago.


    SUSPENSION
    - Upper & Lower control arms replaced less than 8000 miles ago, also included Mehle bushings & ball joints.
    - Tie rods replaced less than 8000 miles ago.
    - Replaced rear sub frame bushings, center link, pitman arm, rear differential support & dog bone less than 6000 miles ago.
    - AirLift Universal Double Bellow bag with air strut (front)
    - AirLift Universal Sleeve Bag air strut (rear)
    - Accuair eLevel air management system with rocker control - If you're unfamiliar with air suspension setups, Accuair is the top of the line in terms of air suspensions & is a no touch, sensor controlled system. The system is calibrated to the car with three different heights: Low, ride height & high. The system uses sensors to constantly monitor the height of the car based on the selected setting and automatically increases or decreases the air pressure to the bags based on the weight in the car in order to maintain its correct height. No manual adjustment is ever needed unless you choose to do so. If you park the car then "air out" the car will automatically return to ride height once you restart the car.
    - Dual polished tanks with hard lines in custom trunk enclosure
    - Dual chrome Viar silent compressors


    BRAKES
    - Custom Futura Design Big Brake Kit installed 12/2013 (front)
    - 2 piece rotor with anodized blue hats (front)
    - Calipers powder coated in Alpine White with blue logos (front)
    - Drilled and slotted rotors (front)
    - Stainless brake lines (front)
    - New master cylinder
    - Rear brakes upgraded to E32 750il brakes


    WHEELS
    Rotiform 3-piece SJC Race - 17x9 square with 3" lips.


    AUDIO
    Sony Audio -
    (1) GS Series Speakers Model number: XS-GS1720

    (1) GS Series Speakers Model number: XS-GS1720S

    (1) 12" GS Series DVC SubwooferModel number: XS-GS120LD

    (1) GS Series 4/3/2 Channel AmplifierModel number: XM-GS400

    (1) GS Series Class D Subwoofer AmplifierModel number: XM-GS100

    (1) Bluetooth Receiver with PandoraModel number: MEX-BT4100P

    - Custom Sub & Amp Enclosure by German Audio Specialist

    INTERIOR
    - Custom Recaro Evo 8 (fronts) completed 10/2013
    - Custom rear M5 rear seat completed 10/2013
    - Custom door cards, handles & shift boot completed 10/2013
    - NRG quick release steering wheel hub & adapter
    - NRG Wood grain steering wheel & matching shift knob


    EXTERIOR
    - Full European conversion
    - European front & rear bumpers freshly chromed 9/2013
    - Front European head lamps
    - Front European grill
    - Rear European all red tail lamps


    BUILD THREAD


    PICTURES


    MORE PICTURES












    .:Rob
    Team16NiSS -AccuAir - Meguiars - SONY Audio

    #2
    oh god... so good.
    this is absolutely gorgeous!
    GLWS

    form.follows.function IG @mplfoster

    Comment


      #3
      holy smokes. that is amazing!!!!! much like in that ride..
      Originally posted by StereoInstaller1
      Yeah, it is expensive but get it anyway, it kicks ass...don't be a cheap bitch:

      Comment


        #4
        W-O-W!! Beautiful build!


        My 1989 e30 s52 Touring... this is Betty

        My 1989 325i vert (sold)...this is Nina

        My 1991 M5 (sold)... this is Veronica

        Photo comparison: OEM vs aftermarket windscreen for a convertible

        Comment


          #5
          Thanks everyone.
          .:Rob
          Team16NiSS -AccuAir - Meguiars - SONY Audio

          Comment


            #6
            What happened to the 504's? Do you still have them?
            1989 US E30 Cammed S52
            Under Construction: 1983 Euro E28 Cammed LQ9/LS3 Heads/Jakeb E28 LSx Kit

            Comment


              #7
              Originally posted by ACHTUNG View Post
              What happened to the 504's? Do you still have them?
              If you mean the Hayashi Techno Rs, which are essentially the same design before being called HRE, they are for sale. 4k with tires, shipped within the US.
              .:Rob
              Team16NiSS -AccuAir - Meguiars - SONY Audio

              Comment


                #8
                Originally posted by UveBeenRobd View Post
                If you mean the Hayashi Techno Rs, which are essentially the same design before being called HRE, they are for sale. 4k with tires, shipped within the US.
                Do you have the metal waffle and screw on plastic center caps?
                1989 US E30 Cammed S52
                Under Construction: 1983 Euro E28 Cammed LQ9/LS3 Heads/Jakeb E28 LSx Kit

                Comment


                  #9
                  That crooked tubing though!

                  Comment


                    #10
                    Originally posted by ACHTUNG View Post
                    Do you have the metal waffle and screw on plastic center caps?
                    It has brand new aluminium waffle centers & and brand new aluminum caps with HRE roundels. No plastic.
                    .:Rob
                    Team16NiSS -AccuAir - Meguiars - SONY Audio

                    Comment


                      #11
                      1991 325i Mtechnic : : 1995 Jeep Wrangler : : 2008 Audi A8l
                      2016 Triumph Scramber : : 1970 Honda CL350 x2 : : 1974 Honda XL 350
                      1975 BMW R75/6 : : 1946 Ben Hur Jeep Trailer

                      Comment


                        #12
                        Originally posted by UveBeenRobd View Post
                        It has brand new aluminium waffle centers & and brand new aluminum caps with HRE roundels. No plastic.
                        What are the wheel's specs?
                        1989 US E30 Cammed S52
                        Under Construction: 1983 Euro E28 Cammed LQ9/LS3 Heads/Jakeb E28 LSx Kit

                        Comment


                          #13
                          Originally posted by ACHTUNG View Post
                          What are the wheel's specs?
                          17x8.5 - 3.5" lips et10 front
                          17x9.5 - 3.5" lips et5 rear
                          .:Rob
                          Team16NiSS -AccuAir - Meguiars - SONY Audio

                          Comment


                            #14
                            All that money spent on body and interior and your still running an M20? WHY not a m30?

                            Comment


                              #15
                              Originally posted by brickwhite View Post
                              All that money spent on body and interior and your still running an M20? WHY not a m30?
                              As I'm sure you know, the Super ETA M20 is a popular platform for forced induction. When I did the EtoI conversion it was with the thought process that I would one day turbo the motor. I've been very pleased with the results of the conversion & am at the point with the car that it's either forced induction or a full motor swap to maybe an s52 or something more untraditional.

                              However reality sets in as to how much any of these routes would cost because I would do a full bay shave & wire tuck if I were going to do it. I just don't know that I want to spend that much more on the car versus moving on to another project hence the sale. If the car doesn't sell, I most likely will move forward in one of the directions above but again I just haven't fully settled on that.

                              As a side note, a great deal has also been invested into a lot of the time consuming maintenance items that are associated with these cars. While some here have balked at the price & told me the car is worth 5k tops, I counter with I beg you to find a car minus all the mods but with all the maintenance I've done for 5k, it's just not going to happen. You can however get into a beaten albeit running E28 for 3-5k and spend your own 20-25 to get it to where this mine is for a fraction of the price.
                              .:Rob
                              Team16NiSS -AccuAir - Meguiars - SONY Audio

                              Comment

                              Working...
                              X