New guibo design?

[badvibrations]

What, a 600 ply rubber disc isn't sturdy enough for 295 ft/lbs?

Fixed.


Maybe, BMW never wants to replace one under warranty again?

[Wh33lhop]

Why is the trans. out of a 2011 335i out of the car and on a stand?

Perhaps it is going into a more worthy chassis.

[CabbE30]

[Jean]

I NEED one, not WANT.

[Ryann]

So I asked today why the trans was out. Apparently the rear main seal was leaking crankcase pressure/vacuum and causing a chirping/whistle noise.

That is some bizarre shit.

[phreshkid]

The future is metal and all we have it little rubber pieces that break.

Or is it the other way around?

[John@Revshift]

Now everybody wants one. Go figure.

[1mz]

in case you have not read it yet, just a heads up.

http://www.r3vlimited.com/board/showthread.php?p=2666607#post2666607

**note - I am not personally speaking for or against the quality of revshift, I have no previous personal experience. But it is relevant to the topic at hand.

[John@Revshift]

Just a heads up.
That thread is not relevant to the topic at hand and furthermore you are speaking against the quality of Revshift just by posting that link.

Did you even bother to read that thread or did you just read the first post and make your decision to call me out right then?
If you did bother to read through the thread you would have found out that the quality of the Revshift parts are not only extraordinary but you would learn that the OP purchased my part with the intent of destroying it, making my company look bad and making a few sales for himself. Now, once again, I have to stand up and explain the case because if I don't people like you will continue to crap on my company and my parts.
This is a simple thing to understand, if you don't have any personal experience with a specific topic then you should just keep your mouth shut and stay out of it.

[1mz]

Just a heads up.
That thread is not relevant to the topic at hand and furthermore you are speaking against the quality of Revshift just by posting that link.

Did you even bother to read that thread or did you just read the first post and make your decision to call me out right then?
If you did bother to read through the thread you would have found out that the quality of the Revshift parts are not only extraordinary but you would learn that the OP purchased my part with the intent of destroying it, making my company look bad and making a few sales for himself. Now, once again, I have to stand up and explain the case because if I don't people like you will continue to crap on my company and my parts.
This is a simple thing to understand, if you don't have any personal experience with a specific topic then you should just keep your mouth shut and stay out of it.

Alright guy, you need to chill out.
From a business stand-point, I completely understand your frustration. However, I did in fact read 90% of that thread yesterday when it was first posted - before it had been 'resolved,' my intent was not to post any misinformation, just make sure that all of the information was in one place. That being said, this is the internet, telling me to 'keep my mouth shut and just stay out of it' is not going to happen, with me or with anyone else for that matter, this is a public forum - If ANYTHING, posting that there will serve to illustrate that your parts are, in fact of great quality - however terrible your customer interactions skills might be.

Personally, I don't like being berated and lumped into the category of "people like you" and accused of "crapping on your company and parts."

In fact, a simple and effective response that would have illustrated your point would have been something to the effect of - "That thread was resolved, feel free to read about the alleged 'issues' and the outcome."

Instead, you act like a dick and make it out to seem that I personally attacked your products... shit.. even WITH my disclaimer there.

Frankly, I hope your 'business' has other, more composed, sales associates that can handle the customer interactions more professionally.

[CabbE30]

I posted this thread in the review one because a fellow member brought up the fact that BMW does use a similar design. I have no experience with Revshifts product nor am I affiliated with the OP of the review.

[Dozyproductions]

Alright guy, you need to chill out.
From a business stand-point, I completely understand your frustration. However, I did in fact read 90% of that thread yesterday when it was first posted - before it had been 'resolved,' my intent was not to post any misinformation, just make sure that all of the information was in one place. That being said, this is the internet, telling me to 'keep my mouth shut and just stay out of it' is not going to happen, with me or with anyone else for that matter, this is a public forum - If ANYTHING, posting that there will serve to illustrate that your parts are, in fact of great quality - however terrible your customer interactions skills might be.

Personally, I don't like being berated and lumped into the category of "people like you" and accused of "crapping on your company and parts."

In fact, a simple and effective response that would have illustrated your point would have been something to the effect of - "That thread was resolved, feel free to read about the alleged 'issues' and the outcome."

Instead, you act like a dick and make it out to seem that I personally attacked your products... shit.. even WITH my disclaimer there.

Frankly, I hope your 'business' has other, more composed, sales associates that can handle the customer interactions more professionally.

You could just as easily read the thread your posting a link to. Wouldn't logic dictate at least that?

[1mz]

Yes, and I apologize. I had read the first 2 pages yesterday, before the 'conclusion' and when I saw this post, I figured they belonged together.

[E30SPDFRK]

So I asked today why the trans was out. Apparently the rear main seal was leaking crankcase pressure/vacuum and causing a chirping/whistle noise.

The Ultimate Customer Complaint Machine!

And my best measurement from the center of two opposing bolt holes is 115mm.

In case anyone wanted to know.

RealOEM lists it at 105mm, but their picture shows a rubber one. Any idea what the part number is?

[Lurker27]

I like it because it looks like bullets for a revolver