Meet Carmela! she is a low mile 325ix

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • stonea
    replied
    Originally posted by f34r
    thanks :)
    i don't think so, i really want an fj63 or an older 4x4 truck.
    Booooooo

    Leave a comment:


  • F34R
    replied
    Originally posted by rzerob
    Wow that turned out awesome. I was wondering about this car.
    Thanks :) I figured I needed to update it.

    Originally posted by Dj Buttchug
    Yes!!!!!!!!!
    Yussssssss

    Originally posted by stonea
    So are you keeping it?

    Personally I think Polly needs a sister.
    I don't think so, I really want an FJ63 or an older 4x4 truck.

    Leave a comment:


  • stonea
    replied
    Originally posted by F34R
    Spent so much time tracking down a rear bumper and a mint door to replace the dented one.

    Up next is a suspension refresh from Sachs and then MAYBE do a 5spd swap(I have a line on a full setup).
    So are you keeping it?

    Personally I think Polly needs a sister.

    Leave a comment:


  • Dj Buttchug
    replied
    Yes!!!!!!!!!

    Leave a comment:


  • rzerob
    replied
    Wow that turned out awesome. I was wondering about this car.

    Leave a comment:


  • F34R
    replied
    I have not posted in a good bit on the status of my iX...she popped a rocker a few months back due to a flat lobe, that brought on a top end refresh. Then I did two stages of compound polish and finished with a cleaner wax and a sealer wax. Spent so much time tracking down a rear bumper and a mint door to replace the dented one.

    Up next is a suspension refresh from Sachs and then MAYBE do a 5spd swap(I have a line on a full setup).

    Enough of that, people only like photos ;D















    BMW head studs




    Now onto the paint:

    The entire car was a faded pink finish.






















    Leave a comment:


  • Kershaw
    replied
    Originally posted by LJ851
    Lift kit + knobbies , Do eet.
    If I get another project, I want to do that to my ix. That would be so bad ass.

    When I had a halfshaft pop out, I put it on a lift and neither front wheels were turning.

    If you lower it, expect the old front cv boots to crack in short order. So you might as well replace those beforehand, before you have grease all over your engine bay.

    Leave a comment:


  • CorvallisBMW
    replied
    Sweet find, sub'd for more

    Leave a comment:


  • Mr. Burns
    replied
    whichever direction you go with this car, I know it's gonna be good.
    Last edited by Mr. Burns; 02-12-2016, 08:41 AM.

    Leave a comment:


  • LJ851
    replied
    Lift kit + knobbies , Do eet.

    Leave a comment:


  • nando
    replied
    make sure the front axles are pushed all the way into the diff. if it still drives with no front wheel action, then the VC must be good.

    And if you're moving to Colorado, I think you would want to keep the ix..

    Leave a comment:


  • Reichart12
    replied
    Rust free is pretty awesome! Nice grab.

    Leave a comment:


  • iXguido
    replied
    Nice ride, I miss my red ix so much!

    The front axles are splined where they meet the diff and are held into the diff with a c-clip. Very much the same as the output shafts in the rear diff. They just push in. Your front DS might be stripped as well.

    Leave a comment:


  • stonea
    replied
    The hubs and axles are held in like they are in the rear, nut and securing plate. I actually don't know how they are secured to the diff. Is it just the half shaft splines on the inner ends pushed into the diff? I've never taken my half shafts out (yet). My money is on TC or the splines on the front driveshaft.

    As for 5 speed; I know nomansland92 isn't using his 3.91 diffs anymore in his build, not sure if he's still using the G260 set up or not. He's somewhere in PA.

    *Also the internals of Auto and Manual TC are the same, drive shafts are the same, its just the diff ratios and the transmission and the TC case that are different.

    Leave a comment:


  • F34R
    replied
    Originally posted by Kershaw
    Nice.

    Either one of your front halfshafts popped out of the diff or your transfercase is toast. Three wheels should spin at all times. Automatic transfercases seem to be around in plentiful supply and fairly cheap too, so that's good.
    I'm throwing it on the lift tomorrow or Saturday, I'm assuming get it off the ground and put it in gear to check for moving wheels. I have only pulled a 5spd for one so my knowledge of the iX drive train is very limited. I would be compelled to keep it if I can find a 5spd to swap(I know they're different). Can the half shaft pop out from turning too far? Or is it a clip/missing pin issue? I know Subaru uses a pin for their half shafts. I have been searching and reading many ix builds/threads to stack some info on these into my e30 data base. I know when maintained they are awesome!

    I know you and Nando are formidable with the ix info amongst a bunch of others here, I look forward to responses :)

    Leave a comment:

Working...